Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi all,
I am using ble mesh code for synchronizing leds in mesh network. I need mesh part, but itshould not integrated with version. So i can able change state of led,...
Hi,
I am a new programmer to the NRF51 and I was wondering if someone would look at my code. I am trying to program the NRF51 to take ADC samples at a frequency of 1 kHz...
I am using nRF52832 with SDK 11.0.0 and S132_V2.0.0 for my application. My beacon is inside Refrigerator where temperature varies from -2 to 20 degree .My Beacon code is in...
Hi,
I'm working on an application with S130 central (client) connecting to an Android peripheral device (server).
I have two characteristics on peripheral device, one...
Hi,
I would like to know what is the switching time between RX ShockBurst and STBY mode?
In documentation I can only find switching time between STBY -> RX ShockBurst...
I don't have a question but am rather posting the solution in case it helps someone else out who had the same problem as me.
With SDK v9/SoftDevice S110 v8, our application...
Hi guys,
I am really confused to distinguish SMP request from pairing request.
Could you kindly what the difference?
Device(nRF51822) can send SMP reqeust? If...
So, I've began tinkering with this device a bit, and using totally stock hex files, installed via
make flash_softdevice && make flash crashes bluez with sigsegv shortly...
I am struggling with the correct value to use for DFU_APP_DATA_RESERVED in the bootloader. My application uses the Device Manager and has one block allocated for to pstorage...
My app is generating hardfualts. Based on this post I looked at memory location SP + 0x14, which points to the address that generated the fault.
Memory at SP+0x14: 8F 31...
Hello Everyone,
I am doing the rough calculation of the power consumption of NRF51 where in the radio part of the datasheet it is indicating 10.5mA whether it is denoted...
Hello ,
I'm using a couple of nRF52 dev.board (one is Nordic preview dev.kit , the other one is a Rigado BMD-300) , with S212 ant+ softdevice . I'm able to deep-slepp the...
I use the board to act as relay.First ,i scan and connect to one peripheral.Then ,i want to disconnect the peirpheral once the another central connect to my board.i call sd_ble_gap_disconnect...
Hi ,
Would you help me to find right material(App note, source code/project) to implement below case:
My nRF51822 connected on beaglebone black(BBB) over UART this will...
