I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Is there any way that can allow the user to advertise a sine wave for example over a specific channel or over the three Radio channels ?
I am using S130 and Nordic SDK 8...
Hello,
As a summary (described fully below) I have loaded the ble_app_hrs example onto my device and its not working right as LEDs that should light up don't and the program...
In some of the Nordic examples I found by viewing the raw advertisements that the company ID is set to Nordic's ID (0x0059). In order to communicate with Apple devices (e...
Hi Nordic Support community,
I asking regarding LNP, Location and Navigation Profile, if it's possible to on top of nordic products? If so like which ones ?
There's barely...
Reading the documentation Address config it is clear how to use RXADDRESSES, could you please explain how to use TXADDRESS ?
As of TXADDRESS there are 3 bits available...
I am having trouble with using shockburst (based on microesb from github) after disabling S132.
When I use microesb with no SD, i just do nrf_drv_clock_init(), start lfclk...
Hi,
I am new to Nordic development platform and am exploring ways to develop software applications to communicate over bluetooth. Presently, I am working with NRF51422...
Hi, I have a problem about gpiote interrrupt.I have set two ports to detect the external interrupt(low to high). If only one port get active ,it works fine. But if one port...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi I am beginner to nordic ble. I have four nrf528** development kit. I am just trying demo heart rate example with android toolbox app. Suddenly one of my nrf devlopment...
I am currently using MBR, and know the general interrupt latency due to MBR + SD from Table 26. But I cannot understand how you arrived at those numbers. IF this table was...
Hello All
Hi, I use nRF52832 with SDK11 Version. But SDK11 didn't provide any CSCS central example. Anybody wrote ble_cscs_c.c for BLE / Cycling Speed and Cadence Service...
Yo men,
I study this web
infocenter.nordicsemi.com/index.jsp
Experimental: Flash Storage
I have 100 bytes data need to read/write/store.
So I think even this is Experimental...
Hi guys,
I compile a provided example with my nRF51_DK and it works well. But when I re-run the program, it will be block in function "sd_rpc_open()". The only solution is...
