Hi there,
I am trying to interface at25xe321d with QSPI but it always end up returning zeros. Please find attached code and dts file for reference. Thanks Moh
Hi,
We have a custom PCB based on the nRF9151 and nRF7002 for a tracking use case, supporting both indoor (Wi-Fi scanning) and outdoor (GPS) positioning. Our firmware is...
When version 1.0.0 of nRF54L15-DK evaluation kit will be available and how to distinguish the version when ordered from distributors like Digikey?
In discussion here:
...
-> How to transfer data from one thingy52 device to another thingy52 device. If i have 2 thingy52 devices, I'll send data to 1st tingy52 then 1st thingy52 device will send...
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
I'm trying to migrate a BLE peripheral app on nRF51822 from SDK 10 and s110 to SDK 11 and s130.
I saw that the new Peer Manager does away with pstorage in favour of fstorage...
We designed a BLE device (based on SDK v10.0.0 + SoftDevice S110). From this device we do a few notifications (through sd_ble_gatts_hvx) between two connection intervals....
Hello I have some question about Keil uVision and Nordic Semiconductor SDK.
My development platform is Keil uVision v5 and my target board is nRF51-DK
I've studied many...
I can't find sample code showing how to send multiple packets per BLE interval.
Can someone share an example or point to one in the SDK?
Thanks
Hani Abidi
Hello all,
I am using the nrf51822 chip as well as an accelerometer LIS3DH. The device does advertising and turns on a LED when it is active.
The accelerometer is configured...
I have implemented multiple application timers who all automatically use the scheduler because I used:
APP_TIMER_APPSH_INIT(APP_TIMER_PRESCALER, APP_TIMER_OP_QUEUE_SIZE...
So im basing my project on your Android-nRF-UART-master example found in github, i don't know if its a app bug or issue regarding the circuit, but first connection is always...
I just started using the RTT and it's been a huge help. I'm working on a multilink application, and would like to have each link output to a different RTT terminal. I use...
Hi !
I'm using S130 softdevice on SDK 11 as central. I'm wondering if there are any conflits in the stack I should be warned. I know it is not allowed to start connection...
So im basing my project on your Android-nRF-UART-master example found in github, i don't know if its a app bug or issue regarding the circuit, but first connection is always...
I want to send over Uart when Button1,Button2, Button3 and Button4 are pressed.
static void button1_pressed(void)
{
printf("\r\nButton 1 pressed\r\n"); //Turn on
}...
Hi,
I'm starting to work on nRF52 with eclipse (on Ubuntu). I use this tutorial to configure everything : devzone.nordicsemi.com/.../
Everything looks good but when I try...
Hello,
I am having difficulty having two nRF24L01P's communicate with one another.
I have set up the devices in what I thought was a minimal system.
I will appreciate...
What is the switching frequency of the DC/DC regulator in the nRF52832? The DC/DC is great for reducing power consumption, but I am worried about the switching noise getting...
Hello.
I am trying to save i/o lines on an 8-pin PIC, and planning to run an nRF24L01P with its CE pin tied to VDD. I am willing to power-down to get out of the RX mode...
