Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi, I am trying to write a small android app to send direct advertisement to particular device.
i am using 0001 for direct advertisment. But when i advertise the data, message...
Hi all,
In my project i want to transmit and receive one character by using 8051 controller. One is act as full transmitter and another one act as full receiver. In my...
Hi, Nordic and all great guys,
I have a weird and terrible problem about our products,which used a MCU based on nrf51822.
Some info about our product:this is a module...
Hi all,
i am using version 11 sdk.
I want to use 2 nrf51822 board in which one will act as master and other as slave.
MY TASK:
i want to transmit "hello" from master...
I have an NRF52832 Receiver chipset board that detects a tag that is transmitting 10 bytes of payload every second.
I have an attenuator on the board before the antenna...
Dear Nordic Team,
I am using nRF51422 development kit. I am work with example code for ble_pherpheral_proxy.
I want to calculate the battery value from the BLE peripheral...
Hi,
I was checking out the forum and I read that its possible to start a timer from the handler of another timer. However it doesnt work for me.
Im using S132 v2.0.0
...
I have developed my prototype using the NRF51DK and now i am making a custom PCB.I currently use the On booard segger debugger to program the NRF51822.Also, i have ULINK2...
Hi all,
I have been developing a program on mbed using mKit NRF51822 and am now ready to move from prototype to one off production.
I am wondering after i create a custom...
I haven't used printf for a while.
Today I am trying to write some code for UART.
but it can only send the first byte of the string to the port according to the scope, then...
I have the nRF51822 beacon kit, using Keil uVision, downloaded the beacon app and all associated files. Compiles, but how to program the beacon board?
I've done two things...
Using nrf51822, Softdevice S110 V8.0 with SDK V8.0.
Sometimes after attempting to erase a pstorage page with pstorage_clear the firmware receives the NRF_ERROR_INTERNAL...
Hello,
I use pstorage to store in nvm some default values after first boot, and change those values via uart commands.
My cb handler looks the same as one in this example...
hello there i have three nrf51 dk. now in beacon code can we do like, when i upload same code to all three nrf51 dk, three will have different major, minor number. can anyone...
