Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Dear Nordic,
We’re working on a Smart Door Lock project built on custom hardware that includes an nRF5340 and several other controllers. For firmware updates, we’ve adopted...
Hello,
I am trying to factory reset 2 nrf52840 dongles that I had very long ago with unknow applications on the dongles. When I erased and installed the image of nrf_desktop...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
Hello, Nordic Team,
I'm currently working on implementing a custom cluster in the Matter application. However, I've encountered issues where the methods described in your...
I tried to build the coprocessor using NCS 2.9.0, but it doesn’t seem to work. Below is my project configuration,are there any additional parameters I need to set?
Hi,
I'm working on a customized version of the nRF Desktop App running on an nRF5340 . In my use case, I want to connect Bluetooth HID devices (mouse and keyboard) as input...
Hi there,
I've designed a custom board implementing the nPM1300 and am currently in the process of examining the board without any firmware. Throughout testing, I have tried...
I am trying to make a simple MAC-layer transceiver using Arduino environment. I have some code derived from this example: https://github.com/IoTS-P/nRF52-802154-Raw-Transmitter...
I’m writing BLE UART code. When BLE is not connected, current consumption is ~30 µA. But when BLE is connected, consumption increases by ~1 mA. I want to reduce the current...
Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
I am getting an error of "undefined reference to `pm_state_force" .
Also, the output files, config file is not showing the command : CONFIG_PM =y
prj.conf file has : ...
Hello,
We have the custom board with nRF54H20. The VDD_EXT pin is used to power some GPIO ports of nRF54H20 (P1/P2/P7).
The voltage we see on VDD_EXT is about 1.3V instead...
Hi,
I am using the nRF52840 with nRF-SDK version 16.0.
At random intervals, I encounter the following error:
"[00:02:51.009,460] <error> app: ERROR 1813 [Unknown error...
Hi,
I want to test the behavior of Enhanced Multi-Admin added in Matter 1.4.
Is it possible to verify this behavior using a Nordic DK board, sample code and a Raspberrypi...
