if the issue can be worked ,how to do that with android source code? the 2 ble pure devices (not android phone) connect with a ble android phone.
please check below, the...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
We're looking for a few (2-3) savvy OS X users who might be interested in trying out Xcode to natively develop code for the nRF51/52 BLE SDK's. This build method does NOT...
Hello,
i'm working with my own board with the SD V6.0 and nrf51822 chip id QFAAG0. Already works fine.
Now i switch to the new SD V8.0. The SD V8.0 is programming with...
Hi everyone,
I'm working on the nrf51822 chip and using S110 stack of SDK 6.1. Everything is fine for IPhone5s. The proximity example is running on the nrf51822 device...
I have used your example of a bootloader nAN_18. I can create a basic program, with new firmware, and also load my new bootloader program at the high end of memory.
My...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hi, I have a nRF5340 using hci_ipc that has the following features:
Central Role + Scanning (Multi-connection to nRF52840 peripherals)
Peripheral Role
QoS Channel...
Hello,
My name is Calvin and I am tasked with testing the NRF52840. I want to create my own development board for prototyping a project, but I do not want to keep plugging...
Hello Nordic team,
I'm currently developing on the nRF5340 and recently encountered an issue related to BLE advertisements . After thorough debugging, I was able to confirm...
I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Description:
I am working on an application using the nRF9160 and encountered an issue where the #MQTTEVT event is not triggered after connecting to an MQTT broker using...
Hi,
I am trying to create a trilateration system with 3 initiators and 1 reflector (Hopefully multiple reflectors in the future) on the nrf54l15. The channel sounding with...
Hey all,
I try to flash the SuperMini nRF52840 using my NRF52-DK over Debug HW (SWDIO pins). I try to flash the Zephyr blinky example.
I think I already got it (at least...
I can flash the chip. I can run the debugger. I can go to the connected devices, select the device, go to the little "plug" symbol on the RTT, and select it. That brings up...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hello,
I'm developing on a custom nRF5340 board without an external clock source - nRF Connect v.2.9.0. For my application, I'm using the internal system clock with this...
Hi,
I am testing the Bluetooth function on my custom board with nRF5340 CLAA chip. I have tested the clock, I2S and SPI on this chip previously and they all worked perfectly...
