Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi,
I would like to read and update value of the characteristic received from AD pin AIN0. I already tested the following code, where I got very weird results (value is...
I am using Keil MDK v5.2 to compile ble_app_uart example using the project in examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I am using the latest nRF5_SDK_11...
I would like to use the capsense example with a Bluetooth application. But as it's not compatible with softdevice, I want to modify it. Two questions:
1 – As anyone already...
HI,
I have very basic question: I plan to connect two devices on i2c to the nrf52. Can they both be connected to the same pins, and configured by software to select one...
I have been analyzing the Bluetooth snoop file on several Android devices, where the Android device is the Central (Client) and the peer device (nRF51822 with S130) is the...
Hi,
I am new to MCUs and I am trying to send information from NRF51 via UART (not BLE UART) to Putty. No matter what I try I can't seem to print anything on Putty. I started...
Hello!
I was copy template project from preinstalled folder to the desire one. When I opened program in new folder, the translate operation work fine. But when I pressed...
I would like to configure the connection timeout with the S130v1. This timeout is described in the following sequence diagram: infocenter.nordicsemi.com/.../group___b_l_e___g_a_p___c_e_n_t_r_a_l___c_o_n_n___m_s_c...
Hi there,
In the process of moving from SDK 10 to SDK 11, I've also been migrating an accelerometer driver over from using straight nrf_drv_twi code to the higher level...
Hello,
Is it possible to use easyDMA to transfer from GPIO to memory without involving the CPU? We need to read from a parallel bus for a short duration, without losing...
When setting up a 1Mhz square wave using NRF_PWM on the NRF52 or GPIOTE on the NRF51 while BLE is advertising, the PWM stops when the radio is active. The problem doesn't...
Hi,
I'm developing a BLE application for the nRF52 and I wish to use directed advertising and the whitelist.
I initialise the Bluetooth advertising using the following...
I have been using softdevice S130 version 2.0.0-7.alpha with SDK 11 in Keil using the pack installer. How do I change my project to work with the updated version that doesn...
Hi,
I believe there's a minor bug in low_power_pwm.c regarding pwm_state.
The routine low_power_pwm_start sets the pwm_state to NRF_DRV_STATE_POWERED_ON ; but it then...
