Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi,
When i want to connect my Power profiler kit II to my laptop, it first blinks GREEN. After i connect to it using the power profiler app, it goes: RED -> AMP (Ampere...
I have a custom board with a nRF5340 and need to configure VREGH in DC-DC mode and set 3.0V output on it.
I see the documentation on REGULATORS — Regulator control where...
Hi,
NRF54L15, nordic sdk version 2.9.1
I recently lost ability to build my application. I get this linker error:
/home/adam/ncs/toolchains/b77d8c1312/opt/zephyr-sdk...
Hello,
Now, I currently run Asset_Tracker_Template on Thingy91X
https://github.com/nrfconnect/Asset-Tracker-Template/blob/main/docs/common/getting_started.md.
And, I...
Hi,
I have a Rigado BDM-300 (nRF52832) on a small custom board.
Using SDK 13.1 with SD132 v4.0.2.
I've taken a template project and adjusted it to my needs. I can get...
Not sure if there is already a worked-out example of converting analog to digital data from AIN0 and then updating a characteristic with that data.
I've worked through...
Hello ,
I am using examples\ble_central\ble_app_uart_c\pca10031\s120 in the SDK 10.00 .
I know that s120 supports up to 8 peripherals. I am using NRF51 Dongle as a Central...
hello everyone:
i use nrf51822QFAC(with 256kb flash and 32kb ram).The project is this "SDK12.3-ANCS\examples\ble_peripheral\ble_app_ancs_c\pca10028\s130\arm5_no_packs"...
Hi all,
I have a board with old code, it has a bootloader + sofdevice 110 + application all from SDK7 and I want to upgrade it via serial single bank DFU, to the SDK11...
I've developed a PCB containing the nRF51822. I am trying to uploaded the example program "ble_app_uart_s110_pca10028" to it, but the chip is not broadcasting (so I assume...
I use buttonless_dfu app from sdk 14
Generate settings file by nrfutil
Merge with bootloader hex file
Erase chip, flash SD, flash bootloader (everything use nrfutil...
Hi,
I am using SDK 12.2.0 with secure DFU service.i want to use pwm in my code.And i init pwm with APP_PWM_INSTANCE(PWM1,1),then i get an error:identifier "TIMER0_ENABLED...
I have built a custom board that is identical in schematic to the nRF52 DK board, with some additional circuitry connected as a SPI interface to the nRF chip. The MCU is the...
Hi,
Glad to see Nordic just released a new alpha version SDK yesterday!
I am wondering when you will release the mesh friend nodes support SDK? I mean support those low...
Hi,
I need you suggestion / information about Nordic chip. We currently have nRF52 (nRF52832) chip. However, in our application we will be using Nordic beacons as an transmitter...
Hello All,
I've finally managed to get Eclipse up and running after migrating from Keil, but now I'm having the following problem: I'm trying to port the buttonless_dfu...
Hi,
Happy Monday! We have multiple PTXs and multiple PRXs in a setting, all operating on a single channel. Is there a way to allow a PRX to receive but disable it from...
Hello,
We have observed fluctuation in Gas sensor readings from Nordic Thingy:52.
eCo2 and VOC readings are not at all near the calibrated sensor readings.
Tried Nordic...
