Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
I am using sdk12.3 with NRF51822 and the original ANCS project. It can successfully bond with iPhone ,but the bonding only takes place at the first time after the firmware...
Hi, I am currently trying to receive a characteristic notification using an Android device which is connected to a ble beacon with the nRF52832 microcontroller. It works fine...
I am trying to pass data to a central device by updating a characteristic. I am calling the function sd_ble_gatts_hvx(m_bcs->conn_handle, &hvx_params) after passing a hvx_params...
NRF52 DK - SDK13.0 - ARMGCC - Eclipse
I am trying to add a custom service to the example ble_app_hrs.
I add all the part per the tutorial and end up getting error 7...
Hi.
I am working on a project which is using SPI and BLE together.
I wrote SPI code before without soft device. It has simple update function which is sending SPI data...
Hi
I did a bunch of boards for a product, and in the latest version I used a BQ25121 PMIC which also has a reset output which I tied to the nRF52 input. On the previous...
Hi all,
There are lots of posts on the devzone about adding DFU service to a custom application and they have been very helpful in getting to this point.
At this point...
I was looking into changing the S130 attribute table size, which is by default set to BLE_GATTS_ATTR_TAB_SIZE_DEFAULT, and noticed that this default seems to be set to zero...
Hi,
I have programmed my nRF52 DK using the ble_app_beacon example from SDK 14 along with S132 V5. I have set NON_CONNECTABLE_ADV_INTERVAL to 3000. I was expecting to see...
Greetings,
I am interfacing AT24C01A(EEPROM) with nRF52 ,SDK11,PCA10040.
For writing to the EEPROM and reading data fromn EEPROM, I am using the following code,
I have...
Hi, when reading the BLE Mesh example code, I got really bewildered by this function:
access_model_add
and inside, there is this gem:
element_has_model_id
...
What's the expected behavior when reading a register that is write only? For example, I'm using an some code that is reading the value of the TASK_START register of the RNG...
Will the Bluetooth low energy advertising tutorial run on 2 x nRF52 DK's and not on 1 x nRF52 DK and 1 x nRF51 Dongle? I wish to test the capabilities of BLE 5.0 (not be limited...
