Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
I have a nRF51-DK. I would like to control the nRF51-DK through my mobile device.
What is the max. distance which can be reach with BLE(nordic chip)?
Is it possible...
Our application uses the S120 stack, and a bootloader. We want the bootloader to be able to update both our application software and the S120 stack (preserving the MBR). ...
Hi folks,
I have been successful in getting sample code compiled using Keil u-vision and MBED and installing it on nrfDK-51. It has become so simple to install apps - all...
Hi everyone,
I successfully compiled and loaded the experimental_ble_app_uart onto my pca10028 board.
I downloaded and installed the nRF toolbox on my nexus 7 tablet....
Hello everybody,
I want to do something very simple: Read some data from my Bluetooth peripheral. I know the UUID of the data I want to read, but I do not know the handle...
Hmm... this should be a simple question. But I haven't found a direct answer yet in the online SDK docs, the ARM NVIC docs, nor in this forum (and have only been confused...
Hi All,
I have a following setup :
The peripheral BLE device is supposed to send **(time critical )**data packets to Central device but the transfer is very rare (Can...
Hi,
I have modified slightly the OTA bootloader sample in SDK6.1 and SoftDevice 7.1.0. After flashing the bootloader code to the nrf51822 it works like charm, I can update...
when i use BLE_GAP_ADV_TYPE_ADV_DIRECT_IND mode,I can see the device advertise (MCP) but i couldn't able to connect with it (advertising_start at BLE_GAP_EVT_TIMEOUT)
i...
Hi,
I'm a beginner with bluetooth.
I'm actually working with nrf 51822 Evaluation board.
I want to realize a transparent mode of communication with your kit. Can you...
I never worked with Cortex M0 before so I wonder how it's possible to jump to correct IRQ handler when I have my own bootloader and application which are using e.g. UART IRQ...
Hi.
Where i can find some information and guidelines to do a good RF PCB with nrf51822?
thank you for your support
EDIT 02/02/2015
Where i can find " nRF51822 Reference...
Hi, I'm using my custom board with NordicSemi nRF51822-QFAA and J-Link.
(Softdevice S110 7.1, SDK 7.2, and using IAR for ARM 7.1)
I was testing the NUS example using...
Hi,
The examples provided seem to indicate that the NRF51822 needs to be attached to an application processor / CPU (e.g. - Raspberry Pi). How much resources (CPU cycles...
