Does the s110 stack allow retrying pairing procedure?
It looks like the stack (peripheral) always ends with disconnect upon invalid passkey.
We would like to explore the...
Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
Is the BLE mesh light switch example of a server and client model the correct implementation for our product?
Our product will include from one to ten devices. For a customer...
Hello,
The question might be a little vague at the moment but I would like your guidance if possible.
I already asked other questions related to this topic but I will...
Hello,
I have been seen some resets on my softdevice v3(SDK12.2) that I am unable to understand,I am using the FPU as well as pheripherial as SPI, I have set up SystemView...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Does increasing the sample time on the SAADC increase the accuracy of a single shot measurement on the SAADC? I couldn't find anything in the datasheet regarding accuracy...
Hello,
I would like to use nRF52810 chip.
And I want to implement PCB trace antenna and PCB chip antenna on same PCB(for provision)
Either PCB trace antenna or PCB chip...
I am using the SPI peripheral for communicating with a network through long wires. Is it any information about the impedance of the driver outputs from the nRF52832?
I will...
nRF52840 OPS v0.5.1 section 16.16.2 states “A pin reset is generated when the physical reset pin on the device is asserted”. This seems to contradict the descriptive name...
Dear Nordic
All our last SDKs in "example/dfu" have same error.
Code is not corect:
nrf_clock_lf_cfg_t clock_lf_cfg =
NRF_CLOCK_LFCLKSRC;
Impossible properly...
Hi Nordic Support,
According to the answer in question:
devzone.nordicsemi.com/.../
it is not possible to update the bootloader (which is the case with "bootloader_secure_ble...
I am trying to set up RTC2 by following an example
github.com/.../saadc_low_power
I ported it to my project which is running a softdevice on nRF52. It works perfectly...
Hi Alls,
I'm trying to compile and test the example project from SKD_12.3.0 and receiving the following error:
#error app_timer for freeRTOS requires configUSE_TIMERS...
Hi everyone
I'm doing some basic test to verify the correct platform for a future project, we need ble long range, therefor we are testing the NRF52840-PDK
I have loaded...
hello,we use nRF24l01+ for the communication of IoT.There are a lot of terminals work at a same channel,when the controllers send CMD,we have found:the length of reading from...
