Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
We are using nRF52840 as SPI slave and imx7 as SPI master.
Data sent by imx7(master) is received at nRF52840(slave) correctly, however the data sent by slave is not received...
Hi,
I have an application where first nrf51 would be the central (remote control) and the second nrf51 would be the peripheral. I got the peripheral to bond with the nRFConnect...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
This is related to another post seen here:
devzone.nordicsemi.com/.../
Basically, I took the peripheral UART example and modified it so all UART printing was disabled...
Hi,
I am using
*nRF52840, SDK13.1, SD140, TWIM, easyDMA enabled. I have tried with the both 0 and 1 instance.
Looking in DSO, I am pretty sure that, after nRF is sending...
I edit the Tx power in ble_app_beacon application (0dbm and 4dbm) using this function and i observing the rssi values in nrfconnect app in mobile.i didn't find the differences...
I've compiled a new app with a new BLE service and module to go along with it (for different work than my other question, I can test this service in a generic LE explorer...
Hi All,
There should be a typo in " nRF24LE1_Product_Specification_rev1_6", page 82, Figure 35.
The Unprotected Program memory is shown 10 kB, but seems it should be 12...
Hi All,
I'm new to nrf51822. I'm developing a battery powered device using the Nordic ble_app_uart_s110_pca10028 peripheral example program. I'm glad to inform you my core...
i want to change the conn_params .
the first gap_params_init() ,
as below: gap_conn_params.min_conn_interval = MIN_CONN_INTERVAL;//20ms gap_conn_params.max_conn_interval...
hi everyone,
I've downloaded s140 and trying to run BLE notification example. I'm able to see state changes in the advertising on putty terminal at COM 7, but when I try...
Hi. i'm using nRF52832.
As datasheet says, flash endurance min value = 10,000.
Isn't there max value?
There is no limited life cycle for flash?
I just wnat to estimate...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hi,
We bought 3 nRF52-DKs (based on nRF52832 and PCA10040 V1.2.1). We compiled, built, and flashed the systems with several provided examples from nRF5_SDK_14.1.0_1dda907...
Hi,
I am working on a project where I have 4 sensors. Each sensor transmits(slave & Peripheral) its value using BLE to the Receiver (Central & master) which is also BLE...
