Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am building an application where a central device is controlled by only one remote control, which is a peripheral device (both nrf52 running S132 v3 softdevices and the...
Hello, as the title suggest, I want to implement an iPad/iPhone mesh provisioner, and this is my general idea:
Build an App which sends and receives customized advertising...
Hello,
I'm looking at BLE 5 advertising packets and the new feature allows to redirect the adv packets from primary frequency channels to secondary ones with an option...
Hi,
I see that the nominal deafult rampup time is 140 us in NRF52.
However, I'm measuring it with logic (via GPIO+PPI) and I get 129.4 us.
Why there is such a difference...
Hi, I received an e-mail about the new nRF52840.
Nordic Semiconductor has today released the new nRF52840 multi-protocol SoC
with on-chip support for the upcoming Bluetooth...
Hello,
I tried the example code ble_app_proximty connect to android using nrf connect application, but why when i try to connect, nrf51822 can not connect, like example this...
Hi /.*/,
i just downloaded the newest version of the nrfjprog command line from the following site:
www.nordicsemi.com/.../58855
Unfortunately after i unpack the downloaded...
Gentle folks,
I'm sure I'm making some simple, primitive error. Please help me mend my ways :-)
Using gcc in the NetBeans IDE on MacOS for building and running the ble_app_hrs...
Hi all,
I have seen thread related to this question such as this and this and I am aware that spikes happen due the automatically controlled refreshing mode of the DCDC...
Hi,
I am working on ble_app_uart_c example provided in SDK12.3.0 with S130. I tried this example on PTR5518 ble chip but suddenly device goes resetted every time.I am printing...
I'm finding rather high power consumption developing freeRTOS on the nRF52. I have it found that it appears Task's are suspending properly on the main BLE thread (copied from...
Setup
I was just looking through the code in the HIDS module in more detail, now that I have built a few demo HIDS apps I want to make sure that I understand the HIDS module...
Hi,
Is there any other define to change than SERVER_COUNT in main.c of client's light control in order to run the example with only 1 client and 2 servers (instead of 3 servers...
I cannot get the output from the is the example the UART buffer gets filled but there is no output to the tty.
The interrupts seem to be set, but I don't see the interrupt...
