I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi everyone,
I would like to create my board like this one :
www.adafruit.com/.../3406
learn.adafruit.com/.../39913
I know that Adafruit changed the bootloader...
I'm using PCA10028, SDK12.3 and android(7.1.1) application using BleProfile.
My application implement ADC using app_timer and indicate adc value each timeout.
The narrower...
Hi,
I have bought a Smart Remote 3 and now I wonder if there is any user manual available for it. I want to test the features it has out of the box before I start to modify...
Using SD130 v2.0.1 on nRF51822, I would like to be able to change the advertisment interval after first connection.
My app is based on the HRS sample, with a modified avertising_init...
Hi,
I am trying to bond Thingy to Android device. But, it is rejected by the device.
How do I bond Thingy to Android device? Any Hints would be helpful.
Thanks
Has the dev kit gone through FCC? i.e. can the SoC/antenna design be replicated on a custom board so there are high chances of passing certification tests?
Hello ,I hope the speed of NUS can be achieved 7K Byte/s. The data form phone to uart is ok,but the data form uart to phone is not.I tested the Bluetooth part separately.Loop...
How to make an encryption on nRF51822?
Does it need to set
sd_ble_gap_sec_params_reply(m_conn_handle, BLE_GAP_SEC_STATUS_SUCCESS, &m_sec_params, &sec_keyset)
the...
I want to flash a client and three servers with the BLE mesh simple light switch example:
infocenter.nordicsemi.com/index.jsp
The third instruction on the above web...
Hello,
I've recently properly started programming my nrf52832 DK with segger embeded studio playing a little with the debuging tool break points modifing example ect.....
I test ble bond with 'ble_app_gls' in sdk 12.3.0
eg.nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_gls\pca10028\s130\arm5_no_packs
my phone is meizu mx4, android...
I feel Slave Latency is unnecessary.
For example :
Connect Interval is 100ms,
Supervisor Timeout is 4000ms.
So the Slave Latency must be 39.
if I set Slave Latency...
Hello,
When using extended ATT_MTU without DLE, and the MTU is larger than the LL data length, I know that the MTU is divided into smaller LL packets when sending.
But...
Dear Nordic Devzone,
I want to run an Arduino Ethernet Shield with the Wiznet5100 on the nRF52840. I was wondering if there was an easier way to do this then having to...
I am designing the BLE solution using nrf52832 . The board will be two layer board with solid ground plane in the bottom layer and signal and ground pour in the top layer...
