Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
[ Just figured out it doesn't work the way I thought ]
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
Hi,
I am trying to run the examples for the pc_ble_driver_py and I get some issues.
advertising.py says "board not found"
heart_rate_collector.py gives a calledProcessError...
Hi folks,
I want to do a project from scratch using the Segger compiler. Where can I find relevant documents with it. How can I make changes on the Blinky project? For...
Hello,
I have two version of Python 3.6 installed: 32 and 64 bit (Windows 10)
Recently i installed nRF5x command line tools (9.7.2) and pynrfjprog 9.7.1
For Python...
In zephyr many PPI has been employed in radio, and other PPI from 20 to 31 is pre-programmed channels and can not use by application. Do you have any plan for optimize this...
hello,
I have one problem to distinguish the following 2 functions :
ble_srv_is_notification_enabled and ble_srv_is_indication_enabled
in on_write function,
the two...
Hi Nordic
I saw the Dfu example.
BLE Secure DFU Bootloader and Buttonless DFU Template Application. I have two questions here. The boot loader and app distinguish a ram...
I'm getting a weird behaviour on my first NRF52 custom board. It's a BLE with HR, battery and a custom service. After programming I can test it properly with/without debugger...
Hi,
I am using SDK 14.0 on nRF52840 (DK), with sofdevice enabled and FreeRTOS port.
My question reagrds the "blocking mode" transfer - event handler was not provided...
I have four PCA10056 Development Boards and I downloaded the SDK for BLE Mesh. The examples, however, only work with the PCA10040 boards. I have tried redefining the board...
Hi all,
We are ready to have our product released and need to have it tested and certified for release in the following markets:
North America = FCC IC
Europe...
Hello,
I would like to configure the NRF51822 as a Peripheral to receive data from a smart phone, and then call a routine when the receive process has been terminated....
I'm using the nrf52832 and I need to stream audio from an SPI connected memory chip, to an I2S connected amplifier. Is there a way I can have the SPI device stream data directly...
Hello,
i have the following setup: nrf52 as peripheral, smartphone as central.
Peripheral's purpose is to be an interface between appliance and smartphone. It has no pairing...
Hello,
For more "simplicity" I have devised my own OTA update procedure. It relies on image information being embedded in a dedicated section (I have modified the linker...
