Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
I have another problem ，when i debug s130 demo by jtag，set free run，the software running OK
，but when i set a breakpoint or stop running，then free run again，the software...
I run a laptop which previously ran this fine on Windows 7 x64. I now run Windows 10 x64.
I cleaned out j-link, nrfgo studio, libusb etc and reinstalled nRFgo Studio again...
I know that it is possible to make 4 PWM outputs, but I need to generate 5. I will be using SoftDevice 110 and BLE. Is there any possible way to generate a 5th PWM output...
Hi,
I need to interface a LED driver (PCA9632) using TWI.
In the TWI APIs I can't see any way to pass the slave address to the TWI instance. Speaking about the nrf_drv_twi_init...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hi, I have an nRF8001 on a Red Bear Lab BLE shield mounted on an Arduino Uno. I'm using BLE to trigger the execution of potentially long running (well, a few seconds anyway...
Hi,
I've done a fair amount with the NRF51822 and Keil on Windows but decided it was time to switch to my native Mac instead of the VM!
Reading all the guides around...
Hello everyone,
I'm a beginner and i'm trying to debug a nRF51422 BLE project.
The SoC is supposed to wait for commands from a STM32 in order to execute some functions...
Hello,
I'm a newbie in this area, and I'm trying to program NRF51822 QFAA on a custom board according to the given tutorial for a dual bank bootloader ( devzone.nordicsemi...
Hello,
Since I am still a little confused, could anyone tell me what S110 and SDK I should use for nRF51822 QFAA? ( infocenter.nordicsemi.com/.../nRF51_Series_Compatibility_Matrix_v2...
i am going to buy nRF51822beacon but i do not know what to buy with it ?
i will buy nRF51 DK but i also want to use a segger programmer with nRF51822beacon.
what confusing...
I was wondering if you could advise me on the best way of adding in BLE functionality to an existing ANT application. Is it simpler to have both transmitting at the same time...
Peripheral receives 4 bytes from central in order to set color of 5 LEDs (1 byte command type + 3 bytes RGB data). There's an iOS app with color picker where user can select...
hi every one.
I need to load softdevice to nRF52 preview DK before execute this app follow it, but i don't know exactly how to do it.
This is my solution:
open...
Hi,
When I reset my nrf51822 beacon firmware using nrfgo, it works just fine. When I try to reset the firmware using jlink, I end up having problems. There are no errors...
