Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I am generating a pwm signal in pin no:21 of nordic nrf51422 board. i connect this pin to pin no:24 using a wire in the same board and want to count only rising pulse edges...
How to decode opus file on Android or how to configure NVS on Android?
we have a Android TV device to connect Smart Remote 3 of nRF52，but audio from the Smart Remote is codec...
I am just trying to program my sample nRF52810 using a PCA10040 devkit.
I get the message "No device detected, or readback protection may be set"
Pressing the Recover button...
Hi,
I'm working on an application with an accelerometer without SoftDevice (for the moment).
The accelerometer communicate in I2C. It send an interruption when a new sample...
hi
I develop nrf52832 based ble device, this based rtos therefore ble communication have critical
time limit.
I will use mesh protocol my ble device, in the environment...
GLS is implemented using Nordic(S110_7.0_SDK6.1).
When set to Control solution function.
The setting of the device and the READ value of the application do not match...
I am trying to integrate an iBeacon Library on nRF51-xxAC with SDK10.0.0 and S110v8.0.0 . Can anyone please help me out if any one has ported the iBeacon Library and what...
I want to implement one central device to ten peripheral devices connections.
I'm using nRF52832 DK and S132 5.0 and SDK 14.0.
So, I have run multilink_central example...
I managed to sniff Nordic mesh sdk 0.9.2 packets on raspberry pi 3 using "hcidump --raw", and I can read the raw hex data of mesh packets of light control demo, but since...
Trying to interface this module with atmel core micro.
We are able to transmit data by this module but not receiving the data at other end.
At transmitting side we are getting...
Hi,
Currently I'm working on nRF52 with SDK11 and SoftDevice S132.
Till now I've worked with IAR and my code was based on the "ble_app_uart" and the dfu "bootloader" examples...
WHAT EXACTLY IS THE PURPOSE OF PPI. IF I AM GENERATING A PWM SIGNAL IN PIN NO 21 AND USING A WIRE I CONNECTED TO PIN NO :24(BOTH GPIOS) IN NRF51422 BOARD AND WANT TO COUNT...
Hey I was using the relay example in SDK 12.2 on the s132 NRF52DK.
We added a service and characteristic using the Nordic tutorial - devzone.nordicsemi.com/.../
Using...
I have a very simple test script which enables a BLE service (only the Generic Access and Attribute), advertises and waits for connection. It also sets four pins to input...
We made a READ request from the client with nRF 52 as BLE peripheral.
READ was automatically repeated 10 times when writing 200 bytes of data in a characteristic fashion...
