Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
I'm new to the nrf51822, i was connected led to one of the gpio pin of nrf51822 development board. In 1 minite i want to toggle led 20sec and remaining 40 sec in sleep. After...
The SDK 12.1.0 documentation for the FDS library says the following:
FDS_THREADS: If set, the FDS module can be used by multiple modules at the same time (for example...
Hello,
I am trying to measure the current consumption.
i could cut the SB9.
and i use analog discovery and measured!!
the picture is shown in below.
gyazo.com/b9f5607148cd9415ea7d1ee6ac644373...
Hi
I have tried to make use of the FDS for storing data and encountered this behaviour.
The required setup of the sys_evt_dispatch() & fs_sys_event_handler(sys_evt) are...
Hi,
were are looking forward to redesign our PCB. The nRF51822 will communicate via I2C which sinks up to 3 mA and 15 IOs will source the maximum rate of 15mA. Additional...
Hello,
I implemented a function to add characteristics to a service, but I'm having a problem when I add notifiable characteristics. I pass a set of flags to my function...
Hi,
I set a debug LED on as the very first thing I do in main. Randomly (sometimes 2 in a row, sometimes 1 in 100), sometimes my debug LED never comes on and no code is executed...
Hey Everyone,
I am new to nordic development. I am really used to programming with easy environments like the Arduino. I have seen some examples using the printf() command...
Use the Nordic \ nRF5_SDK_12 _f012efa 2.0-3 d \ examples \ peripheral \ pwm_library routines, now can output two lines of PWM, but want to two way different PWM phase have...
Hi there. I'm Matthew!
I noticed that there were contests sponsored by Nordic in the past, such as
Startup Weekend, June 15-17, 2012
The Nordic Semiconductor App...
I can use nRF Toolbox as a central to test various nRF5 as BLE peripheral samples.
Is there any sample app (iOS or Android) to test the few nRF5 as BLE central samples? ...
Hello.
I am trying to turn off ACK in the example "esb_ptx". I have tried this in both SDK 12.2 and 14.0.
I try to turn off ACK like this:
static nrf_esb_payload_t...
Hi,
I am trying to establish a border router in my test Thread system (a part of infocenter.nordicsemi.com/index.jsp . I have the required Raspberry Pi 3B, but it is driving...
I'm using the 1.0.1 nRF Sniffer and 1.10.10 Wireshark on Windows 10 64bit. The firmware 1.0.1 is programmed to nRF51822 dongle using Jlink 6.12a. The exe works fine when no...
