Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hello,
I've been using UART DFU feature quite extensively in one project which caused that I had to stick to SDK11 features (since bootloader relied on SD 132 2.0.0). ...
I couldn't see this in the documentation, but I might have missed it. Does the Logger Module consume additional power when it is enabled/initialised? If it does, presumably...
Hello,
I have developed a board with the integrated nRF51422 QFAA. I have the nRF51DK.
To compile I have used both mbed and arm-gcc and the binaries work perfectly on...
Hi everybody.
I am making a firmware based on ble_app_uart example (PCA10028 NRF51422, Softdevice S110, NRF51 SDK9.0). In this firmware, I insert dfu part ( follow by this...
I am testing out the Bluetooth Mesh SDK 0.9.1 Alpha using the light control client/server example. The examples have not been modified.
I have set up a nRF52 development...
In android while at the stage of scanning there is list of ssid ,i am getting print of scan_result but while trying to print the RSSI value,the result is 0 .Files i have changes...
With our custom board, I have implemented the battery service and it's working well. But the nus service is not shown up at all, the same initialization code as the official...
i use the nrf52832,s uarte. using the app_uart_fifo.c document. but i can only receive the max 256 bytes.the configuration is belows:
APP_UART_FIFO_INIT(&comm_params,
...
Hello,
Is the characteristic value data supplied to sd_ble_gatts_characteristic_add() and sd_ble_gatts_value_set() copied into the softdevice RAM, or does the softdevice...
.pdf d051cefddbc197cd7d)
Hello All,
I am working on Automotive project using nrf51824 SOC...
Hi,
I am working on making a test harness using the nRF52DK and a raspberry pi so I may run unit tests directly on the nRF52832. I want to use the UART to give test results...
We recently did pre-compliance RF radiated immunity testing at a certified lab. The EUT was nRF52832 on a battery powered post card sized circuit board with some sensors....
when I run the program I get this error
Checking installed packages
pyside: 1.2.2
pyqtgraph: 0.10.0
numpy: 1.11.3
pynrfjprog: 9.1.0
Warning: The software is tested...
I am using a PPK with v1.0.0, but elsewhere in DevZone I see references to later versions of the software. Where can I download the later versions from? Have I missed a link...
