Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
Hi,
I am nrf52832 SDK14 .
Can you provide a simple example of IRK implementation to resolve the peripheral address in SDK 14.It will be helpful to get insight of it. ...
Hi,
Do you know why I get a warning : Unable to allocate memory for relay packet. ?
I am trying to mesh 2 servers and 4 clients. with client capacity 3 for each server...
Hi,
I'm trying to run the gdb on the nRF52 with softdevice s132 and in the begining it runs ok but after some time when I run (gdb) list I get: "Line number 435 out of...
Hello,
I'd like to send 16 bits data over ble instead of 8 bits
gatts_value.offset = 0;
gatts_value.len = len;
gatts_value.p_value = data;
err_code = sd_ble_gatts_value_set...
The call to ble_x_handles_assign() is not uniformized on all the examples. It's sometime call from on_ble_evt() or/and from x_evt_handler() .
From the doc on the function...
What shoul i do? 0 erro with code
SEGGER J-Link GDB Server V6.20d Command Line Version
1. JLinkARM.dll V6.20d (DLL compiled
Sep 29 2017 16:44:59)
Command...
I am using S120 Softdevice, with bunch of different type ble tags(peripherals). written a code to connect multiple tags at a time and doing a gattc read to fetch the battery...
I have a technical issue I am facing while doing development with Nordic NRF52840. I have an application which I am sending command though virtual com port using CDC ACM USB...
Hello everyone!
I am learning with nrf52840 MCU and SDK version 13. When I read the example. I see one line:
SVCALL(SD_BLE_GAP_CONNECT, uint32_t, sd_ble_gap_connect(ble_gap_addr_t...
Hi,
I'm developing a project based on nRF52 and utilizing NFC for my master's degree. One part of the project will be a beacon with as small PCB layout as possible. That...
Hi,
Often when I try connect BLED112 dongle to bluetooth module BMD-300 by command:
ble_cmd_gap_connect_direct(DeviceMAC, gap_address_type_random, 60, 76, 100, 0); ...
hi,
i want to add uart function to my application. so i added necessary .c files to my project. if i compile the program i am getting these errors.
when i change the...
Hi,
I have Raspberry PI 3 Model B Rev 1.2 running "Linux raspberrypi 4.9.41-v7+ #1023 SMP Tue Aug 8 16:00:15 BST 2017 armv7l GNU/Linux". Running BlueZ 5.43
I can connect...
Hi community,
Try use FDS to write some data before sleep.
Following example and test is work.
But I try write data before into
sd_power_system_off();
...
