Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
Hello, I'm working with the EK PCA10003, that has the NRF51422. I'm trying to read the information of the accelerometer MPU6000 with an ISP interface. At the moment I cannot...
when I run the secure bootloader example in nrf51422 development board, the code is working fine. I am able to load the packet through nrf toolbox app. But the same code when...
hello
i am using nrf 52840 board with sdk 13.
i use heart rate collector example to connect the 6 heart rate peripheral .
Modified the hrc_c example following this link...
I want to monitor NRF radio channell's RSSI to switch on "free" channel.
How to make it properly?
This is my code:
if(rx_q_flag == true){
err_code = esb_init(RX,...
I want to increase the MTU values to increase the throughput from my own service (currently based on NUS service) and to receive the data with pc-ble-driver-python with the...
I am using power_manage function to keep low power sleep mode. And I used below peripherals in code,
SPI master, SPI master is disabling when ever I am not using.
...
It appears to me that some of the saadc APIs (e.g. those found in nrf_drv_saadc.h in SDK 1.4.0) are missing in the nrf SDK for HomeKit.
Some hint where to find these functions...
How do you do
The attachment is a problem in the previous code, please help to debug it, thanks ble_app_uart_pwm.rar
E:\nordic\nRF5_SDK_12.2.0\examples\ble_peripheral\ble_app_uart_pwm...
Hello.
There is an executable file built by setting the address of the entry point (RO_Base) to 0x00000000 with Keil's linker setting.
I converted this executable file...
Hi,
I'm using nrf52840 with openThread. I like set the MCU in system on low power mode. RTC1 is used as application timer for wake up and start transmission periodicly. For...
Hello,
I could not find any related info, so I would like to ask few questions:
I have pca10028 board, using s110, sdk 6, ble_app_uart code. The board gets connected...
Hello all,
During current measurements of our product using nrf52832QFAAB0 I've noticed a high IDLE current of ~450uA. Trying to isolate the problem we programmed our board...
I am working on adding DFU, persistent storage and pair/bond feature to an existing nRF51 application, developed with SDK v10.0.0 running on SoftDevice S110 v8.0.0.
I looked...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hello,
I used translation software.
I am transferring test data from nRF52832.
I want to down the average current consumption in data transfer.
I am currently...
Hello,
here i explain the set up.
Cental_A Board :- scanning two peripheral
Peripheral_A Board :- advertise with name Peri_A .
Peripheral_B Board :- advertise with...
