We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
I have device from another company that has a n51822 chip for BLE UART communication and it can send data to my phone via an app with no problems. However, I am having difficulty...
When I add an attribute with BLE_GAP_CONN_SEC_MODE_SET_OPEN I get a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST event when I try to read it.
I do not however get a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
My application involves driving a digital-output (PDM) MEMS microphone at 1 -- 3.25 MHz with a clock generated on a GPIO.
devzone.nordicsemi.com/.../
The output of the...
Hi, I have a custom service with 3 characteristics and i've been attempting to send one of them as a notification so I can use it in the HRS sensor app by changing the UUIDs...
Hello,
I am working with the nRF51822 and S110 Softdevice. I have so far successfully created several examples of fairly complex Peripherals. Now I am trying to,
A)...
Hello,
If we use same hardware and antenna design of one of Nordic DV/EV kit, can we shorten bluetooth LE certification process?
I see Nordic points the following app...
Im trying to run the example blinky_example on BLENano (tried with gcc / nrf51822-sdk on linux and windows)
.hex from linux before merge : 8475 bytes
.hex from windows...
I'm looking at the downloads for the nRF51 DK which has the nRF51422 core. I'd like to put the s110 softdevice onto it, but I don't see a download for s110 on nrf51422, just...
Hello,
I am trying to use the s120\multilink_central example, using SDK v6.1 and S120 v2.0. The probleme is that I get a hardfault handler. I think that the probleme is...
Hi, I am using a nrf51822 with sdk 7.2.0 and s11o v7.1.0
I also have a imu ( mpu 6050 ) that gets accelerometer and gyroscope data.
How do I do continuous transmission...
Hi,
I am using the nRF51 Dongle and every time I send a command the pipeline goes into "Stall" condition. Using USBlyzer I can see that the command is sent but straight...
Hello,
I would like to build a device that looks for other beacons (not using a phone)... This device would simply look for other beacons near this device.
My questions...
I just tested putting the same firmware on two different nRF51822 s and inspected them with this test app .
They show two different UUID's.
I can find no macro...
Hello guys!
I'm experiencing some troubles trying to compile the blinky_rtx example for my new nrf51DK. The source is taken from the SDK7.2.0.
I'm under Linux and I...
