Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
Hi,
I'm trying to run the gdb on the nRF52 with softdevice s132 and in the begining it runs ok but after some time when I run (gdb) list I get: "Line number 435 out of...
Hello,
I'd like to send 16 bits data over ble instead of 8 bits
gatts_value.offset = 0;
gatts_value.len = len;
gatts_value.p_value = data;
err_code = sd_ble_gatts_value_set...
The call to ble_x_handles_assign() is not uniformized on all the examples. It's sometime call from on_ble_evt() or/and from x_evt_handler() .
From the doc on the function...
What shoul i do? 0 erro with code
SEGGER J-Link GDB Server V6.20d Command Line Version
1. JLinkARM.dll V6.20d (DLL compiled
Sep 29 2017 16:44:59)
Command...
I am using S120 Softdevice, with bunch of different type ble tags(peripherals). written a code to connect multiple tags at a time and doing a gattc read to fetch the battery...
I have a technical issue I am facing while doing development with Nordic NRF52840. I have an application which I am sending command though virtual com port using CDC ACM USB...
Hello everyone!
I am learning with nrf52840 MCU and SDK version 13. When I read the example. I see one line:
SVCALL(SD_BLE_GAP_CONNECT, uint32_t, sd_ble_gap_connect(ble_gap_addr_t...
Hi,
I'm developing a project based on nRF52 and utilizing NFC for my master's degree. One part of the project will be a beacon with as small PCB layout as possible. That...
Hi,
Often when I try connect BLED112 dongle to bluetooth module BMD-300 by command:
ble_cmd_gap_connect_direct(DeviceMAC, gap_address_type_random, 60, 76, 100, 0); ...
hi,
i want to add uart function to my application. so i added necessary .c files to my project. if i compile the program i am getting these errors.
when i change the...
Hi,
I have Raspberry PI 3 Model B Rev 1.2 running "Linux raspberrypi 4.9.41-v7+ #1023 SMP Tue Aug 8 16:00:15 BST 2017 armv7l GNU/Linux". Running BlueZ 5.43
I can connect...
Hi community,
Try use FDS to write some data before sleep.
Following example and test is work.
But I try write data before into
sd_power_system_off();
...
Firstly the develop environment.
Windows 10
KEIL as IDE
Device: nrf 51822 - sd s130 2.0.1 - SDK 12.1 nRF5_SDK_12.0.0_12f24da.zip
Use case:
We have 2 application mode...
Hello i am using segger studio i have recently purchased three nrf52dk speically for ble mesh..
i am trying to run examples of mesh alpha sdk that nordiac prvodies but it...
