I am working with NRF52840 with SoftDevice S140 and SDK v17.1.0.
The boot loader address for this chip is 0xF8000. I can set up one of the 'fstorage' module with the address...
Hey everyone,
Does anyone here have experience with firmware OTA updates over the JIO NB-IoT network? The process seems a bit different since JIO Cloud always sits between...
Hello:
The latest nRF54L15 Errata for Rev 2 shows that the previously reported "GPIOs can exhibit radiated emissions" is no longer present in the Rev 2 SoC.
Can you please...
Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi,
I fail receive data from SPI.
I have check the signal from oscilloscope, there slave does reply SPI data to master. So, It is definitely is code problem.
Below is...
Hello,
We are testing ble beacon based on nRF52832. We have incorporated DC-Dc in our design. The design has fractus antenna. Our previous design was without DC-DC. Now...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
Till now we were using nRF Connect app...
Hi All,
I am trying to assemble the ble_app_template project (nRF5SDK160098a08e2) in Eclipse. Has somebody some more detail instructions on how to compile new projects...
Hello,I am new to this field.I dont know how to interface QMC5883L Geo-magnetic sensor which is 3-axis magnetic sensor with nrf52840 and read the temperature and axial(x,y...
Hello,
Could you please help to create a list of reasons (or get a reference to it) when node may fall out from network?
Removing network credentials on the node
Key...
I am getting killed by the fact I cannot restore the CCCDs on a bonded reconnect and need to rely on the client doing it every connection - a violation of the standard.
...
Hi Team,
Please let me know can we register Multiple e-sim in Thingy:91 and nRF9160/DK? What is the procedure for e-sim registration in Thingy:91?
Regards,
Ashiq Mo...
Hi
I am testing the example ¨¨ ble_app_att_mtu_throughput ¨¨ on nRF52840 by changing different paremeters incuding data length, MTU, transmitting power and PHY.
when I...
Uisng pca10040 and SDk16.0.0 + Segger
I built and ran the GPIOTE example so I could experiment.
I want to toggle a gpio once only and then stop and I need to know when...
Hi,
Iam looking for very simple low cost wireless module which supports at least 500meters range ,please suggest a module.
I dont need lora module apart from this please...
I have latest SDK, which is nRF SDK 16.00. I have noticed that not all the examples are available for PCA 10100.
So my question is what is the difference between the PCA...
Hi,
I have compilation error to use SPI.
Checking project status Building ‘ble_app_beacon_pca10056_s140’ from solution ‘ble_app_beacon_pca10056_s140’ in configuration...
Hi,
I am trying to get the nRF-IEEE-802.15.4-radio-driver found at GitHub to run on my nRF52840 DK.
Does anyone have a check list or can explain how to link the files...
Hello,
I'm wanting to start a project with the NRF52840 DK in Segger Embedded Studio. I went through almost all of the tutorials and set up the SDK.... etc but I have...
