In our development using NCS-2.6.1 it is desirable to have logs using BT NUS.
"Serial Bluetooth Terminal" android application is used.
For testing purposes NCS\v3.0.2...
Hello,
I'm trying to hold the TX line of UART0 low for 1 second. I'm using NCS 2.9.0 on an nRF5340.
Disabling UART and setting the pin directly works.
But after reenabling...
Hi,
I want to port an exisiting solution from ESP32 + nrf24 to nrf54L15. I didn't find any example that would work out of the box for my POC which would to combine very...
Hello,
I am working on a hardware design with two MEMS PDM microphones and a mono speaker. I think I have the peripherals allocated and wired correctly but wanted to run...
Hi,
I'm trying to connect to the EMQX(what I made on GCP) using mqtt protocal. I'm using the sample code that nordic provides in lesson. Based on the Exercise4 code which...
Hi I'm having the exact same issue found in this post:
I've only just started evaluating the board and haven't gone as far into measurements as that poster, but something...
hi,
my device is nrf52832
i run my spi sd card driver fine in debug mode, but when i download it ( F8 ), it can not work!
so my question is what is the difference...
Hi,
I need to monitor radio channels and find the best one (with lower background noise) to use.
Is there any way to measure radio signal level in a particular frequency...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
I'm trying to get a simple "Hello world" program to run on the Nordic ID Medea.
As soon as I start debugging I get the error "The bootstrap could not be loaded".
Any idea...
I follow this:
developer.nordicsemi.com/.../a00092.html
Creating an image file
The format of the firmware image that you use to update the device firmware depends on...
My problem: The run of my 1. DFU - Implementation delivers an error code after executing the line "err_code = ble_dfu_init(&m_dfus, &dfus_init);". For my opinion this is caused...
At the moment I am working on a project that uses the nRF52328 acting as both a peripheral and central to connect 3 separate devices intermittently. I am storing their bonding...
Hello,
I use SDK example nfc_text_record for pca10040 DK.
With aim to check memory area of the emulated tag I've modified example with next:
/* Set up NFC */
err_code...
Hi,
i am working on PWM to operate vibration motor with different frequency levels. so that i integrated PWM Library example to my ble_app_uart example. in the PWM example...
Faced with problem in subject during porting Serialisation to STM32F4 chip.
Serialisation library extensively uses function call triggered by NVIC.
How to substitute this...
I'm using ANSC example, pca10028, iphon5s and iphon4s.
I confirmed #define DEVICE_MANAGER_MAX_BONDS 7.
But pca10028 cannot pair with iphone5s after paired with iphone4s...
Hi,
I'm using nrfutil to update my nRF52832.
I change target from nRF51822 to nRF52832 and I want be able to bootload my target through own master.
In past, I used...
I have followed instructions at the link below to setup a Raspberry Pi 3 as a 6lowPAN router, and am trying to run the dns example from nRF5 IoT SDK 0.9.x on an nRF52-DK:...
Hi,
I'm using pca10040 and prebuild hex with s132 from sdk 12. Now I'm wondering how can I get number of sent data? If I set it as transmitter - send via uart 0x8094 i...
