Hi,
I recently updated Nordic connect SDK and toolchain from v2.7.0 to v3.0.1. When compiling my application with activated CONFIG_BT_LL_SOFTDEVICE flag, I get this error...
Hello Team,
I am currently working with the nRF52832 and using the nRF Connect SDK ( NCS) with toolchain version 2.9.1. I would like to interface the nRF21540 RF Front-...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
I have installed nRf Connect for Desctop v5.1.0 on my windows 11 system.
I tried to update the Quick Start and install the Power Profiler.
Both gave me a similar error...
Hey All! I've been following the nRF Connect SDK Intermediate course from DevAcademy. In exercise 2 of lesson 9, bootloaders, you get to learn how to use KMU (Hardware Key...
Hi,
Testing Hardware: nrf52832 Module in a Custom board OR nrf52DK possbile -> We would like to change the order of the BLE service as shown in this thread: https://devzone...
Hello, I am trying to use the nrfx driver example to run an RGB led connected externally to the nrf5340 board. I dont see the led/pwm cycle running successfully. Can anyone...
Hi,
I am new to eclipse on windows.
I have bought the PCA10040 board.
I have installed eclipse and GNU ARM Eclipse 3.1.1 plug-ins.
Copied the NRF52-SDK into workspace...
Hi developers,
I am trying to collect data from an AFE (ADS1298) and could get some values. Inorder to check the accuracy I need to plot this value. I am programming this...
Hi,
I am running the nRF51822 from a coin-cell. I need to measure the cell voltage. Until now, I have attached VDD to an ADC pin with a voltage divider and a capacitor...
Hello~
In my production line use jig contact my PCBA, and use Jlink connect to Nordic 51822 download FW, but I found sometime can use 500kHz and sometime can't use, just...
Hi
I am using nRF52(PCA10040) as a sniffer dongle, but it seems the sniffer mode cannot work, and shows the error log: "INFO: Error on port xx. file: Packet.py, line 245...
First step of trying to integrate S132 to a small OS is failing completely.
When I use SVC the system ends up in hanging in hard fault.
The SoD handler ends up trying...
I am testing to develop an application that sleep (system-on mode) for most of the time, and it wake-up periodically to send out somethings.
As I would like to lower the...
Hello,
After when I download the protocol stack（S132）.The target is NRF52832 chip，tool is J-link OB.
I choose to recover nrf52 ，then prompt unable to fine or open the...
Hi,
In ADC, we would be using the internal voltage generator as the reference voltage. How stable is the voltage coming out of the reference generator. Would it be always...
It appears that, if I wanted to write characteristics to my BLE device, I can utilize the writeCharacteristic method of the BluetoothGatt class. Is this the right way to go...
Hello,
I am currently for a quick solution to test NRF24LE1 compliance to FCC. Can you provide me with any code if possible? As i could see from the website only an application...
Hi,
We can utilize the 31 bytes of advertising packet as well as 31 bytes of scan response packet which in total makes it 62 bytes of advertising data. What is the effect...
Hi dear Nordic Engineers.
We going to move from FN-LINK (Realtek) I.C. BLE to nRF52.
FN-LINK uses HCI (UART) BLE the Interface to communicate with our embd. LINUX.
How...
Hi all,
I'm using pca10040 board with sdk version nRF5_SDK_11.0.0-2.alpha_bc3f6a0.
There i'm using example code of spi handling. Instead of nrf_log_printf i changed...
