hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I'm currently wprking on my project, my project it's about swarm, before the master swarm can advertise the message to the slave swarm through blehandler function now...
Hi,
My unit based on NRF52832 with SDK11 and works as pheripheral.
I started my project from nordics NUS (Nordic uart service) example.
My IOS software developer wants...
Hi Sir,
We got the nRF52833-DK, and tried to program the nRF52832 IC through the nRF52833-DK.
We download the latest version of nRF connect and command line tool, but...
Dear,
I am using THINGY:91
I am trying to read the data from BME680 sensor:
1. config: ( i used conf file from asset_tracking)
and, get the temperature:
...
Hello,
I am using UART1 to communicate with sensor. It is working fine. I can receive the data. Now I want to modify this data. When I use strcpy() function, it works properly...
Hi Team,
We are trying to make Nordic NRF52840DK board to act as a server (BLE ) where as we are trying to connect other board (Not the Nordic chip) has only transmitter...
Hello again, I accidently verified one of my own answer so I will retry.
I am currently trying to update the firmware for Thingy 52, using the NRF52 development kit. ...
I'm using a nrf52840dk as peripheral and iOS (iPhone 8) as a central. They are to be paired. The pairing routine is already implemented and works fine. The problem is that...
Update: Was me being a dumb ass and calling the advertising start higher up in code that I thought I disabled. After truly disabling the BLE, I was able to debug and found...
Hi,
Overview: In our board BMD340 (containing nRF52840) module present with GSM module and they exchange data using UART(PINRX-6,PINTX-7). Now we trying to use "ble_app_uart...
hi,
i am using one central and 18 peripherals. i am unable to send data to one particular peripheral from the central .plz help me to identify a peripheral in the group...
Hello, We were interested in a new SoC nRF5340, but I would like to determine some points in advance:
peripheral blocks remained the same as in nrf52840. Or were changes...
Hi there,
I would like to add the device address of a central to the whitelist on my peripheral. Is this possible without bonding? So I set sec_param.bond = false in pm_sec_params_set...
Hello.
I am working on ble project and using uart communication between bluetooth and stm32. I need to reinitialize uart module in case of any error in event handler but...
1、nRF52830。Does the dongle included with the product support the over the air packet capturing function of Bluetooth?
2、We need Bluetooth to grab packets. Do we need a third...
