Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi,
I need nrf_malloc and nrf_free for my application but I cant find which files should I include to be able to use thees functions.
Thank you very much
Hi,
I would like to evaluate the long range demo with the 15.2 SDK (original 15.0 is used). Opening the project and trying to compile it gives some errors like "no such...
Hi support team,
I have found that RESN and RESP are typically 160 ohms, customer would like to know their stability and temperature coefficient.
Regards
Salas
HI,
Version: SDK15.3,ble_app_template,custom board with nrf52832
I'm trying to change my device name by writing data from bluetooth
when getting 0xdd 0x06 ........,it...
Hi What is the minimum clock frequency that the TWIS module will work with? Obviously the I2C spec minimum is about 100kHz however the device I am communicating with is using...
Hi,
Is it possible to use the modem firmware mfw_nrf9160_1.1.1 (delivered with nRF Connect SDK 1.2) with nRF Connect SDK 1.1?
We will move to nRF Connect SDK 1.2, but...
Hello, we are integrating a BLE board (nrf52832) into our system, and the ble_app_uart example project is perfect for us, so we are starting with that.
What we are seeing...
After reading some questions about the Thingy:91 here in the forum, I start asking myself, if the Thingy:91 without a nRF9160 DK is usable at all.
Any experience with that...
Hi, I'm working on a design with nRF52832 + chip antenna. I'd like to add a PI network to be able to tune the antenna before production.
I'm working with this antenna:...
OK, I have an app that succeeds in starting advertising and then arrives in the main event loop, following which I go to the NRF_BREAKPOINT_COND trap.
Since I do not have...
hi,
I am using Running Speed and Cadence Service structure, when i raise a write command (bt_gatt_write) from the client I was expecting a BLE_GATTS_EVT_RW_AUTHORIZE_REQUEST...
OK, so I have figured out that I can put some of my advertising content into the scan response if there is no room in the advertising packet, but what do I do if there is...
I just bought the nordic thingy91 and managed to connect it to the cloud. but since then the device doesnt appear to come on at all? I thought the battery has died but when...
My application is using multiple features such as BLE UART, Proximity and TWI.
I've two twi sensors triggered when needed. and one of them generate an int to wake up the...
