Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
Hi,
We see that in documentation V1.1 there is this info on a pin added.
"AUX - Single-ended 50 Ω ANT loop-back pin"
What is the function of this pin?
Documentation...
I found several threads with same questions. And also found source codes.
But they are too old and require Legacy support for KEIL and old softdevice.
Is there actual source...
Hi,
The product is peripheral, CPU is nRF52832 and I use nRF5_SDK_15.2.0_9412b96.
My customer asks me how many bonded amounts support in our product?
because I can't...
If I enable the zephyr shell inside my project with the following config; I'm not able to see anything on the UART If I have CONFIG_SERIAL=y in the SPM prj.conf, If i disable...
hello:
I am using ble_central\ble_app_blinky_c example and attempt to be a central scanner to scan and connect to many BLE peripheral nodes.
The name of target BLE peripheral...
Hello.
We are running an application without BLE at this stage. We measure about 20ma at run time also by the datasheet max is 6ma.
We were thinking that because we don...
Hello All,
I purchased nrf9160 DK board for sending text message using AT Commands. I programmed the SIP to accept AT Commands. Using the LTE monitor app, I tried to initialize...
Why Nordic doesn’t consider update of already 5 years old nAN-36 Creating Bluetooth Low Energy Applications Using nRF51822 ?
It is the most meaningful tutorial for starters...
I recently obtained a PPK from Mouser and plugged it in my nRF52DK. I use it to measure current of an external device.
When NRFConnect "connects", it works great. However...
Hi,
I'm using the latest release of software V1.0.0 with the nRF9160 DK and today started flashing the examples.
at_client worked fine (just tried flashing it once, but...
Hello once again Nordic World,
We are preparing code for production, and one of the last issues to resolve is how to "uniquely" connect our ble_app_uart peripheral based...
Hello,
I'm working on NRF52832,using SDK16 Segger Embedded Studio
now the thing when upload APP_NOTIFICATION it works and also discoverable.
but when upload APP_UART...
Hello.
I just found here: https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/firmware_architecture.html
something like this:
"To turn on sensor...
I am trying to trigger my target device (nRF52832) into DFU mode using nRF52832 DK.
According to my approach, I need to send DFU bootloader given in "installed folder:\examples...
