Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
On November 19th, I participated in the 2019 Nordic Tech Tour with my colleagues, but some of the content was not clearly understood, especially regarding the development...
Hi all. I want to measure current consumption on nRF52840 DK (PCA10056).
I have the SB40 cut and the 12 Ohm resistor placed in R90. I measure the voltage on this resistor...
Dear team：
How can I use ble-bas-c to change Characteristic UUID or Connect the 1800 service and rename it with the 2A00 feature value The example is \SDK\nRF5_SDK_15.3...
Hi,
I am new to this. I want to build a mesh network using nrf52832. I have already downloaded and gone through nrf5 SDK for mesh but i am confused about what to use to...
I am using nrf51822 DK. How to set GPIO pins as output pins and access the pins to set or reset the output.For example if I want to use pin 20 as output, how to configure...
I am trying to read if an input is 0 or 1 but for some reason it takes the first one its offered and then it does not change anymore.
int main(void)
{
nrf_gpio_cfg_output...
<Environment> - nRF9160 DK v0.8.5 - nrf tag: 1.1.0 - modem version: 1.1.0 - using an external GPS antenna, SW12 => CON
I'm attempting to use udp_gps, but doesn't work out...
Hi all,
I'm a bit confused. After going through available documentation, I thought I had understood that RTC0 was used by the SoftDevice, but that RTC1 was available to...
Hi,
I am using nRFmesh SDK for a project. I have configured all nodes(devices) into one group. Each device will publish message for every three seconds. I am reading the...
Hi,
I need step by step guidance on how to implement BLE MESH ( SIG MESH) using nRF52840 Dongles.
I am trying to connect 5 dongles in MESH config.
Kindly help with...
Hello. I am using nRF52832. The SDK version is 14.0.0. UARTE is used for serial communication with other devices. The baud rate is 38400bps, and a maximum of 20 bytes of data...
Hi, I could not find a way to use Segger Studio debugging features when I have a bootloader for DFU functionality. Is there a way to something like that, because when I click...
I am trying to read temperature, pressure, and humidity data from an Adafruit BME280 sensor using the nRF9160 DK. The communication protocol that I am using is I2C and I am...
Hi,
In our product, we use 9160 GPIO to control the system power. However, we found we can't power off when 9160's modem is in normal mode. But, the system can power off...
