GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi all,
Good day.
Could you please recommend an Android or IOS APP which can connect 8 or more BLE peripherals at the same time.
Thanks & Regards
Jenson
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
I am currently working on an ultra-low power project that requires reading an I2C accelerometer multiple times per second. After analyzing the current consumption...
Hello,
we've got a problem with iOS 10 connecting to a peripheral using nrf51822 with S110. When bonding an iOS device to the peripheral the first time it works o.k. If...
Hi,
I am using BMD300 to develop my projects. I am working on SAADC sample example in SDK12.0.0. I am sampling the SAADC at a rate og 1000 sps. following is the saadc_ini...
Hi,
I want to set the reset bit to 1 in the reset register of Power Management module.
Chip used in nrf51822.
I have been trying to set the bit using the following statement...
how to send hex by nrftoolbox APP uart?
I use this app, when I start use it, I just only can send char, I can't send hex to the device. how to set it char to hex? please...
I am using the Nordic nRF51 SDK on a BLE Nano device. The example I am using uses a function to initialize the LED flashing (bsp_init()). This sets the timing for the ticks...
Hi all,
I want to use nRF51822 (s110) to measure the frequency (0 to 5kHz) of a signal connected to an analog input. Other posts ( like this ) show that a good way to implement...
Hi,
SDK:8.1.0
Chip:nrf51822
Power Mode:LDO
Battery:CR2450
Application:beacon
The equipment static power consumption is 3.3 ua, after a period of time is 1.9 ma,but...
I'm using Keil5 to compile example of SDK v12.2. And I'm trying to understand each of Source code to understand how each of it is consists of.
I opened an example "SDK...
My code hit weak handler when I try to modify the examples/peripheral/saadc to run with softdevice s140 on nrf82840 PDK. All I did was adding a BLE Stack initialization before...
On the nRF52832, what is the longest period of time that the softdevice will control the CPU while doing things with Bluetooth? This is effectively the interrupt latency time...
I am working on nRF51 and nRF52 series SoC.
I need to check whether my radio device is connected or not and also to test radio functionality(like radio range, sensitivity...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Is it the only way to call a function on a read characteristic to make a read request and then inside on_ble_event call the function?
Is this the right way?
