Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hello,
We're thinking of powering external sensors through GPIO pins configured as high-drive. The sensors themselves consume only a few milliamps at most, which is easily...
Hi,
I would like to control a piezo driver using GPIO pin on nRF52840 DK.
I've read posts about this kind of application. But still confused about how to set up PWM...
Hello again Nordic Pro's,
I have a mildly modiffied version of ble_app_uart_c that compiles and runs fine on an NRF52-DK board. I am now trying to use the same code on a...
Hi,
I'm very new to the Nordic BLE chips. Sorry in advance for asking stupid questions, but I'm willing to learn! This is my first project for my current job, I want to...
Hello,
I've been trying to run the OpenThread mqttsn_client_publisher example from the SDK. I have also set up the border router according to the tutorial on the infocenter...
Hi:
I meet a strange softdevice assert when I do dfu in nrf52832. There is no info or call stack for this assert, I only get the assert is NRF_FAULT_ID_SD_ASSERT.
Do you...
Hi,
I have been working with the Thingy:91 at the version 1.2.99 but this also happens on previous versions (I do not know which it was but the serial_lte_modem code had...
Hello,
I am facing a issue with the LN service. I am notifying the position at 10Hz and this work well. I have implemented a custom service that allows to send a file by...
Hi,
Just as the title says, I want to use nRF52840 as a peripheral(s140, v7.0.1, BLE_NUS_MAX_DATA_LEN is 244) and using NUS.
And it may pair to a nRF51822(s120, BLE_NUS_MAX_DATA_LEN...
Dear
I got a problem about SES when I create a indepent transferable project for PCA10059.
Background:
I have success to modified a light-swich server from PCA10056...
Dear All,
I need to understand how the Asymmetric Encryption work in BLE. From Nordic, I get to know the following that following are the nrf_crypto frontend modules
...
Hi,
I"m looking for a solution to automatically build the emproject file from the directory *without using any IDE) so that i can export the .hex file and can be used...
Hi.....
I get the following error fault from my device (nrf 52840 with freertos ,using SDK16.0)
the Fatal id: 0x2000B730
what caused Fatal id: 0x2000B730 ?
Hello,
I developed a project based on thread CLI example. Everything works fine but I would like to add more commands to the CLI interface, maintaining the existing Thread...
Hello:
I am using nRF Connect v3.3.1 programmer to flash nRF9160 and got an error.
Silk on nRF9160 is: nRF9160 SICA B0 191601
Programmer can't recognize nRF9160 after...
