Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hello,
So I assume VDD is from USB or the battery depending on whether USB is there or not. So, when the SAADC outputs ~3.258 V (in low power mode) that's fairly correct...
I need to measure with SAADC two channels in the same time (NRF_SAADC_INPUT_AIN6 and NRF_SAADC_INPUT_AIN4).
Is possible ?
Have you an code example?
Thanks
Marco
Hi,
I used a nRF51 dongle (PCA10031) wit the nRF Connect (v3.3.0) Bluetooth Low Energy application to communicate with a MBN52832 development kit. This works great until...
Hello:
I am looking for the best way to capture the SD and application error/fault(s) so that when the device is restarted, the data can be transmitted to the central...
Hi
I have installed the toolchain according to the getting started assistant, nRF Connect SDK v1.1.0
I try to load the asset tracker application in Segger with CMake_lists...
want to add UART communication to nRF52832 with mesh enable.
I have added,
nrf_drv_uart.c
nrfc_prs.c
nrfc_uart.c
nrfc_uarte.c
files into nRF_Drivers folder...
Hi,
Let's say I have a network with 5 NRF52833-DK and 1 smartphone with the NRFMesh App. How can I achieve to sniff all the ongoing packets in the mesh network on the smartphone...
Hi,
I have a customise board which has nrf52832 chip inside. I want to establish a secure connection between my 2 customised boards but I dont have any button or display...
Hi,
We are currently in development of a custom board with an nRF52840. I'd like to check my IO pin mapping using an IDE if possible, but I was unsure if Nordic or its partners...
Hello. I am using a Nordic Semiconductor Beacon (nRF 51822) and i am trying to connect it to my Raspberry Pi 4, but even though i installed Bluez, scanned using hcitool, i...
Hi,
I have nrf9160 DK. It is ok for ibasis SIM card. But if verizon SIM is used, there is no TCP/IP connection.
I tried to set APN by using:
AT+CGDCONT=1,"IP","vzwinternet...
Hi,
I'm trying to deploy the example program, cifar10, from CMSIS-NN library on NRF52. The issus is I compiled and downloaded it to the board successfully but when I try...
Hi,
I'm trying to combine serial UART functionality into the USBD_BLE_UART example. The goal is to send data in/out to the hardware UART as well.
I started off by loading...