Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
We are planning to run the nRF52840 in CKAA configuration 3 (attached) in Normal Mode. When we boot, our regulator will provide VDD = VDDH = 1.8V. Reading through the...
Our product is using NRF24L01+ and PA to transmitter data. It pass all the test of FCC PART C but the BAND Edge measurement.
The below 2 pictures is NRF24L01+ Band edge...
Hello everyone,
I have been dealing with this issue for some time now, and I think it's time to find a definitive solution, I am sure there is one!
For my projects,...
I had some questions when using nRF5SDK160098a08e2\examples\dfu\secure_bootloader\pca10056_s140_ble for OTA test. Who can help me answer my question?
1. Can I return the...
Hi,
i have created some custom characteristics and i am enabling read and write characteristics in that, but when i am trying to write or read some data it seems that it...
Hi everyone,
I am trying to connect my nRF 9160 DK and Thingy:91 to TIM (Telecom Italia Mobile) CAT-NB1 network provider from Brazil. I am using the Asset Tracker and...
Hello,
For my project I want to use broadcast packages to send data to multiple devices at the same time.
I've seen that there is a beacon application that "should"...
Hi,
I'm trying to develop a custom service and am following a few examples in trying to do so. The software crashes for me everytime after advertising the new service...
I am building a custom device that incorporates the nRF9160. For testing I would like the device to work in China. I believe NB-IoT is the only network that is supported by...
Hello,
I have multiple records that I want to update during the runtime of the program.
What is working:
1. I can write in memory for the first time initial values...
Hi ,
I am using nrf connect 1.2.0 dk. I am now testing the https client example.
However, I always get the connection fail error as belows.
Provisioning certificate...
Hi:
I want to send pictures and voice.So it needs to be faster.What should I do?
I use nrf52832/sdk16.If nrf52840 is used, can it reach 2Mpbs?
Measurement example:nRF5_SDK_16...
Hi there,
Here is what I'm trying to do. I'm trying to use the 52832 as a badge to be used by people in order to report the zone the person is in using a ble mesh network...
HI:
My IC: nRF51822QFAA My SDK Project: ...\nRF51_SDK_9.0.0_2e23562\examples\ble_peripheral\ble_app_template\pca10028\s110\arm5_no_packs
Appearance：
When I Powerup or...
