Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi,
I got a question on nRF52832 platform. When it is brand new (so without loading any of our FW) and powered through 3V3, it draws up to 4.6mA when powered. But we also...
Hello,
We have seen the below error,
NRF_ERROR_INVALID_ADDR If the EasyDMA is used and memory adress in not in RAM.
While trying to connect with an external sensor hub...
Timer A with a 10-minute interval, timer B with a 4-hour interval, and timer C with a 10-second interval are required, and A and B should also run out of time in low power...
Are there any updates on coded phy support for the nRF sniffer?
I found a thread about this from "over a year ago" which says to check back in 4-5 weeks: https://devzone...
When CENTRAL connects how can I read the UUID and ADDR of the peer?
static void ble_evt_handler(ble_evt_t const * p_ble_evt, void * p_context) {
switch (p_ble_evt->header...
Hi Team,
We are facing issue with Flash storage Handlers with ble handlers. When we add the fstorage to my application ble adversing is stopped suddenly.
We are having...
Hey,
I want to use a standard 16bit service and to add some custome characteristics to it, will this create any compliance issues? Is it complying to BLE specifications...
Hi all,
I'm using the "ble_beacon_app" example from the SDK 16.0.0 with the nRF52840 DK. I would like to change the TX power level.
In main.c function, I tried to change...
Hi All,
We tried to modify the Android source core of nRFTools for our Proximity application . And we used some nRF52832 and nRF52840 as the proximity device.
1) We connected...
Greetings,
we are developing a custom board that holds a nrf9160 chip. We have uart lines out on pins 28 and 29, as on the DK. We need to use the AT client in order to flash...
I've implemented a Application and Bootloader. I have the Bootloader set to Buttonless. However when I try to transition from the Application to Bootloader via:
/* Sets...
Nordic team:
We are developing a proprietary application for Android tablets using the Android-BLE-Library and have been experiencing issues with scanning after a long period...
Hello
I'm very new with nRF modules and currently struggling with BL652-SA-01-T/R module to run Bluetooth.
I have developed small pcb to test this module, PCB includes...
Good day,
I am using the ANNA-B112 BLE device from ublox in a custom design. The ANNA-B112 interfaces with a host MCU over UART. The ANNA=B112 is flashed with Soft Device...
Hello I have an application which requires the use of both BLE and Openthread in the same time. The BLE is meant to connect an OpenThread mesh network to a smartphone.
I...
