Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
Hello,
I want to read two files from SD card using nRF9160dk. I tried this code ncs/zephyr/samples/subsys/fs/fat_fs.
The Code:
I am getting the following error:
...
I need FreeRTOS operation in my build. I've adopted the FreeRTOS.h file from the blinky_freertos example, unchanged aside from a larger heap size and setting INCLUDE_xSemaphoreGetMutexHolder...
Hi all,
I have the nRF51822 chip and I want to acquire external sensor (i.e. pressure, temperature) and send the information via bluetooth.
I need to configure the I/O...
Hi
I using nRF52840-DK with 64 Mb external flash memory.
I'm using SPI interface for read / write command with the external flash.
When I'm using single command for...
I am attempting to implement AoA using the nRF5340 Preview development kit and 3 BMD-360 modules with the nrf2811 SoC.
In searching the devzone I see multiple comments...
Hi ,
I am following the instructions here:
https://bifravst.gitbook.io/bifravst/bifravst-on-aws/simulator
to deploy the web application, and the web application says...
Based on SDK15.3(nRF52810) app_uart example, stop the adverting, turn off all the peripherals and enter idle_state_handle(), but the static current is still about 10uA. Rememeber...
I set up the environment for the nRF9160 as it was specified and downloaded the git-hub code https://github.com/NordicPlayground/fw-nrfconnect-nrf (environment 1) and I tested...
Hi all,
I am using 2 SPI's in my design. I enabled SPI0_ENABLED and SPI1_ENABLED in my sdk_config.h.
SPI0 works fine. But SPI1 MOSI pin always sends 0xFF.
My pin configuration...
Hi, I m sending a packet in mode Nrf_1Mb to another board nrf5340-PDK.
When I try to enable NRF_REGULATORS_S->VREGRADIO.DCDCEN=REGULATORS_VREGRADIO_DCDCEN_DCDCEN_Enabled;...
Hi,
I am using mesh SDK v3.2.0 and SoftDevice(s140 v6.1.1) to build light switch server firmware. And also insert the uart code from nRF5_SDK_15.3.0_59ac345. So the light...
Hello:
I am studying thread samples in nRF9160.
There are two thread samples: "zephyr\samples\basic\threads" and “zephyr\samples\synchronization”.
But I can't find main...
Hello,
I received information that i could turn the modem on and off not more than 60 times within an hour.
We are however working on a real time system, which may...
Hi everyone,
Currently I am routing hardware for an upcoming project using the nRF5340 and it's time for a sanity check.
The goal is that the HW works well enough w/Engineering...
Hi,
I've been trying to set up a SPI <-> USB interface between an FPGA and my PC via the nrf52840 dk. My ultimate goal is to stream 1Mbps+ worth of data, but right now I...
