Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hello there
I am now using Nordic 52840 dongle hardware ready to be used as a zigbee sniffer, and I have seen that official documentation is feasible.
My current environment...
I am having trouble modifying simple_hal.c from the mesh SDK v4.1 when buttons are on Port1 instead of Port0 on a nRF52840. I have buttons on P1.01 and P1.02.
Everything...
We're attempting to move from v1.1.0 to v1.2.0 of the NCS, in order to take advantage of some driver improvements (particularly DPD in the SPI NOR driver. When we migrate...
Hi,
I am currently working on a custom product that uses module BMD-300 from u-blox, which has nrf52382 chip in it. My application works fine and now I want to integrate...
hi,
Im developing a mesh network based on the nRF52832. I want to send some long message(over 11 byte) without segment, so I enabled the EXPERIMENTAL_INSTABURST_ENABLED...
I turn on the Instaburst feature already , after that , I program serial example to 2 nRF52832 and run it with interactive_pyaci
when i try to do PacketSend with 20 bytes...
I am running a Bme280 sensor with nrf9160 and getting this error msg ( [ 1;31m<err> i2c_nrfx_twim: Error 195952641 occurred for message 0 ) while getting the actual sensor...
Hi All,
Since I measured a very current consumption by testing CLI example (ftd/usb) I'd like to know how to switch my nRF52840 DK as Sleepy End Device.
Any suggestion...
I have a zephyr sample app running on a nrf51822. It's the onoff_level_lighting_vnd_app found in samples/boards/nrf/mesh. I have an iPhone running nrfMesh. I can't find documentation...
Hello, Im working with nrf52832 and sdk15 I'm working with the example: nRF5_SDK_15.0.0_a53641a/examples/ble_central_and_peripheral/experimental/ble_app_hrs_rscs_relay I want...
How can I receive all the packets from all addresses?
In the datasheet I see there's an RXADDRESS which setups the receiver to which address it will listen to. I want to...
I am using the zigbee sdk4.10 cli_agent_router and multi_sensor example. The 52840 module is E73-2G4M08S1C, antenna is a built-in ceramic antenna. During operation, the communication...
Hi,
I have central based on the 840 and a Peripheral on the 833 , I Need to ability to upgrade the peripheral version from the central.
I know that there is no example...
Hi All,
I am trying to use the RNG peripheral through the softdevice (i am using Version 5.0, with 14.2 SDK) with the sd_rand_... functions. I have enable d the RNG in...
