Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I loaded up pca10056e ble_app_beacon example for SES to test it on a custom nrf52811 device I have built (using BMD-360 module).
I followed the instructions here and removed...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
I want to know the life of FLASH by garbage collection. Assume that garbage collection is performed only when "PM_EVT_STORAGE_FULL...
the python package is not updated through pip with last release of SD_API and corresponding hex files.
I know that you give instruction to build driver but it could be easier...
I am trying to test a simple non-connectable BLE adverstising. I am using the following resources.
1. SDK - 16.0
2. SD - S132
3. Board - NRF52 Development kit.
4....
hardware: nRF9160 DK 0.8.2 firmware: 0.7.0-29.alpha
I want to send data every a few seconds through MQTT. It fails in the first and second Tx after MQTT client initiation...
Hi there,
I am having a hard time with some C pointers to add a new BLE Characteristic.
I would like to have a function that returns a simple characteristic metadata and...
Hi , I am using nrf52840 dk with zigbee cli example in sdk. I have configured nrf52840 as coordinator. I am using xbee pro s2c modules as router in zigbee network. Terminal...
Hi everyone,
I want to send my IMU's readings through BLE to a central. I have implemented the code and notify the central every 1s with the measurements.
I have an array...
Bonjour, je ne peux pas télécharger un firmware via l'application nfr toolbox avec mon Huawei p8 pour mon home trainer connecté, via bluetooth. Je reste bloqué à 2% et un...
I'm working on a solution and facing a few difficulties. well, I have more than 100 smartphones (android and iOS) devices in closed proximity were all the devices are logging...
Hi,
We have an embedded flash of 4Gbit which stores sensor data. The data needs to be transferred to a Smartphone. Now we are using USB cdc acm for transferring data with...
SDK 16.0
52810
S112
From the sample code of SDK we can see that the UART is enabled by code ourself, as the following. However, what's the usage of the NRFX_UARTE_ENABLED...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
Please tell me the operation when garbage collection is executed. The setting values of FDS are shown below for reference.
We...
I am trying to program my custom board nrf52811 by pca10056 using ses, and i was able to flash any example of nrf_SDK, however the LED does not blink. even though i added...
SDK: 15.3.0 Device: EYSHJNZWZ (nRF52832)
The following contents are described as the description of "FDS_VIRTUAL_PAGES". "One of the virtual pages is reserved by the system...
