Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
Hi,
I am trying to save some data in flash by using the Flash data storage.
However, everytime I try to write data to the flash, the module returns this error code:
FDS_ERR_UNALIGNED_ADDR...
Hello,
I'm making bootloader(nrf51822xxAA SDK12.1.0 and SD130 version).
I have some problem in micro-ecc installation.
To install micro-ecc, complete the following...
Hi, I have a problem with DFU OTA.
I use nRF Toolbox's DFU to upload nrf51822 QFAC, most times it works.
However several times, after the app altered "** bytes transferred...
Hi,
I want to generate a 2.048MHz clock on one of the IOs of nRF52832. Could you comment on following questions?
1- Can I generate this frequency (with no load on CPU...
Hello, I work with some ADC 24-bit (HX711) and for getting data from that I need after low level on first gpio pin to fed 26 pulses to that with time period about 1us on second...
Hi,
I am using ble_app_uart_c_S120
How can i support more then 1 bonded connection?
i try:
#define DEVICE_MANAGER_MAX_CONNECTIONS 7
#define DEVICE_MANAGER_MAX_BONDS...
What's the correct settings for nRF51822 CEAAE0 (0x0079) with dfu example in SDK v11 ?
I believe the chip I am using is a 16KB ram 256KB rom version, but not sure 51422 or...
reco_scan_req.PNG
Now i am doing a test of RECO beacon which use a nordic chipset, nrf51822.
But something strange came up to me during the test with Ellisys bluetooth...
Hello,
I know that this question has been asked in the past but I could not find any recent post about this topic, and there have been many updates to the SDK since the...
I am using NRF52DK and SDK 12.1. I am using BLE. I currently am not using Peer Manager but probably will be implementing that in the future (of sooner if that makes my question...
Actually, nRF 52832 DK has Type-2 NFC Tag. For type-2 NFC TAG, its data access method can be read/write or read only. Therefore, does Nordic have any example codes of two...
Hello,
there is written that Peer Manager is using flash for storing bonding data or service configuration. Can you extend a documentation - and add description when and...
Hello,
I have platform base on nrf51822, collecting data through I2C and sending to android application.
the device is working according following protocol:
Motion data...
Hello,
I'm developing firmware for a BLE central that performs a DFU on another NRF target. Right now I'm at the point where I need to start sending the firmware image...
