I have a zephyr zbus project running on the nrf52840DK that’s working well. We want to port the project to the nrf54H20DK, but I’m having trouble seeing the log messages....
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi.
I'm using nRF51822, SDK10.0.0, S130.
I made "radio test" program as below at the first.
void radio_tx_carrier_test(unsigned char freq_ch)
{
NRF_RNG->TASKS_START...
Hi,
Can we add device address with all fields set to zero's to whitelist.
I went through the spec, but it doesn't talk about the address set to zeros.
Thanks,
r...
Is it possible to change data send in scan responses after each Advertising Event? I know that sd_ble_gap_adv_data_set() has constant input arguments, but it seems weird for...
Hi everyone;
Im trying to use my nrf51822 as iBeacon with "ble_app_beacon" in SDK. As you know for estimating Distance, you should calibrate it. for calibration, place...
Hi,
I have IOS application which works fine with bluetooth different than NRF. I use direct connection by UUID in IOS app. When the application is in foreground everything...
Dear Sir,
I am new in nRF51 and used the ble_app_uart example in our application (nRF51), need power saving function but not necessary power off.
The sample code will...
Hi,
I am trying to implement timeslot API using s110 v8.0.0, SDK 8.0.0 on nRF51822-XXAA on a keil uVision 5 platform.
I have tried the following memory settings:
...
Hi
Regarding the NFC url example there is any way to change the URL dynamically. My idea is to, at a certain point, be able to modify the URL configured during the setup...
Hello,
I'm having an issue when trying to update the bootloader itself: NRF_UICR->NRFFW[1] returns 0xFFFFFFFF, which means I can't use the MBR command to swap bootloaders...
Our BLE product uses a meander PCB antenna similar to PCA10031. It works actually quite fine, but a question pops up when it comes to tuning.
Antenna matching design in...
I'm having some issues getting the auto ACK to work properly. I am only receiving auto ACK messages on the first 3 received packages, after which the receiver stops replying...
Hello i have a system that build in an ultrasonic sensor RedBearLab BLE Shield ( nrf8001 ) and arduino i want to get ultrasonic data via bluetooth and see it on nRFConnect...
Hi,
My host MCU controls nRF51 over SWD interface.
How can stop/halt nRF CPU? After initialization the SWD(init/read DB/AP AHB, etc.) I need to halt (stop nRF program...
Hi,
I would like to have one page of flash mapped manually to store information critical for the device. Let's assume I do not trust data preserving by DFU or there is...
I have some BLE traffic that I have sniffed and am displaying in Wireshark. Most of the opcodes (read/write request/response indications/notifications etc.) are parsed/displayed...
