Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Is it possible to send and receive data with the thingy91_at_client_2020-04-29_bc7ade8b?
I found, that this is not supported by AT commands, instead socket libraries for...
Hi everyone,
I have created a custom BLE service with a characteristic and I update the custom value after enabling notifications by calling the ble_cus_custom_value_update...
Hello,
I am integrating saadc example to ble_uart in order to receive analog input signals and send them via ble connection to android application. Low power consumption...
Dear Nordic Team,
We are working on connecting an I2C device to an nRF52840 Dongle . The code we are using is one we've been developing for a few weeks with an nRF52840...
Hi,
For BLE softdevice, I am wondering if it is possible to set connection supervision timeout to infinitive, which means the connection will never be considered lost? ...
Is the process of communication between QSPI and Ext. flash same for QSPI and PSRAM? If not, what could be the procedure?
And how can I communicate with 2 PSRAM using single...
Hello, I want to create a device, that can auto-connect to my phone and only my.
I thought to do it by filtering the MAC address.
But as far as I understand iPhone and...
Hi,
I was trying to find my way configure and SRAM which has QSPI interface. However some commands are different and cannot find how to modify and adapt the qspi module...
SDK 15.3.0 documentation says:
"Error codes are 32-bit unsigned integers with the most significant 16-bit reserved for identifying the module where the error occurred ....
Hi
I am currently trying to design my own custom board with just the nRF52833 SoC. I am using this for AoA and I/Q sampling. I had a few questions.
1. What is the...
A quick question. I've made an App based on the peripherals not required by the SoftDevice, in particular s112 states RTC0 and TIMER0 are used. I'm moving onto the Bluetooth...
I am able to run all samples from this folder /ncs/v1.2.0/zephyr/samples/ and see the output on the LTE Link Monitor.
However, when I try to run the GPS sample from /ncs...
Hello I notice that exemples with Softdevice ( nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b) works fine for a PCA10056 but not on a PCA10059. When I had tried to make this...
Hello,
first of all let me thank you for providing the nRF Sniffer, which is a great and very helpful tool! I use it a lot and I'm well are that one would have to pay a...
