Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
I am working with the mesh 4.0 light switch example and had a general question regarding a custom model I created based off the simple on off model.
During configuration...
Hi,
Our application sometimes hits a breakpoint in SoftDevice at either address 0xA60 or (less often) 0xA80.
Based on this post https://devzone.nordicsemi.com/f/nordic...
My question is very similar to this .
I am posting again since it did not seem to be answered.
The error originates from the following:
This happens when I am trying...
IAR IDE can be used to develop and dug the code of nRF52832 . However , IAR IDE can not programme the flash of nRF52832 directly . I need a kind of flash programmer tool ...
Hi all,
I am working with Segger ES on chip nRF52832 with nRF SDK for Mesh v4.0.
I am stuck now at message publication.
I have discovered that my code runs to packet_send...
Hi,
I'm using the nRF52832 with FreeRTOS and SDK 14.2.0 . I took a look at Profiling the Softdevice and FreeRTOS with Segger SystemView and Instrumenting with Segger SystemView...
Hello,
I am using nRF5 SDK v16.0.0 on nRF5232 PCA10040 DK.
I am trying to create an application that will count the number of button presses (GPIOTE events) using a Timer...
Hi.
I'm using nRF52832.
There are some NC pins in my schematics.
How to control them to save current consumption?
Making them output and low is the best solution?
Hello,
Is it possible to configure the board as a peripheral device that provides the Nordic UART Service and allows multiple central devices to connect and exchange data...
Hi Technology, I use the Keil 4 version of the IDE, the chip is Nrf52832.Open examples-code appears this problem, how to solve?
Installation of NRF driver library package...
Hi,
I'm interested in using data signing for authentication since encryption is not wanted. However, I have not found any support for this. Currently I'm using softdevice...
Hi.
we setup a project according nfrconnect --getting started assistand,but it fail in seggerstudio,
we use sdk1.2.0(cd ncs/nrf • git checkout master • git pull • git...
I'm using fstorage to store logged data in Flash. Works well, no problems there.
What I'd like to be able to do though, and haven't found a solution to, is to be able to...
Dear,
I am working with THINGY91
ncs_1.2.0/Modem FW_1.1.1
SIMcard: Telia (LTE_M and NB-iot) / Horten.Vestfold.Norway
I am looking for information about AGPS, could...
HI,
Is there a minimized version of the relay example that shows how to transfer a message from device to device without the art of the HRS?
I hope it will be less than...
