I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
I've been experiencing this bug for a while now. What happens is that a app_timer's overflow handler can't put any more messages into the queue because the queue is full,...
I need to connect to the VSS of the nRF52832-CIAA Ground
A mistake by one of the VSS was not connected nowhere.
The VSS was one N.C..
Do you have any problem with...
im sure the reference design is copywritten if i added two components and removed the GPIO breakouts and switches and led is that in any way not ok? i know nothing on RF signals...
Hi. I am trying to add DFU service to sourse code with existing service. When I try to run service without device manager + DFU or run device manager + DFU without my service...
Hello!
I am trying to build a connectable Eddystone beacon with a Blend Micro board which uses nRF8001 . I used the BLEPeripheral library ( github.com/.../arduino-BLEPeripheral...
Should I call app_sched_execute at least once before the first app_timer_start ? I have a strange bug and I realized that calling it before is a fix but I don't see this in...
Maybe this is a newbie question but, I read that using TEMP is a restricted resource for the SD but I could not find any driver or example to use it correctly.
Can someone...
I am trying to determine the suitable set-up to determine when my system's battery source (lipo battery) is too depleted.
I am running my nrf52 at 3 volts and the Lipo Battery...
Hi. I try to fusion 's130_nrf51_1.0.0_softdevice' and 'flash write'. I checked flash write. but when i implement flash write with s130 softdevice, it is not working. If i...
I have the nRF52 dev kit, and I hooked up pin 13 to SDA and pin 18 to SCL on an I2C device. There are no external pullups on the SDA or SCL lines.
However, the TWIM module...
I tested some features of the new nRF Connect application version 1.0 on PC. The application has a lot of interesting features useful to develop and debug embedded software...
Hello Everyone!
I want to make a project that will recognize some tone in the air, up to 5KHZ, and will send nrf8002 a message as a result.
I though to use the nrf52 proccess...
I am using SDK_11 s130 ble_app_gls on nRF51-dk.
An Android phone running nRF-Connect app was able to pair and bond with nRF51-dk. First time doing pairing and bonding works...
