Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
hi support team,
docs says we can program 54l15 external spi flash ,please refer to : https://docs.nordicsemi.com/bundle/nrfutil/page/nrfutil-device/guides/programming_external_memory...
NRF2460 is linked，I can transfer 3 byte data. But sometimes it is mute, not always.
Register I2SCNF_OUT bit6 is zero.
I am appreciate for your advices.
I have problem to start the wireshark with this plugin error. The last I checked the nordic_ble.dll file is there in the folder.
The procedure entry point new_creat_dissector...
Hi, I'm new to Nordic. I can't get 250Kbps working on the nRF24LE1. I'm using the enhanced shockburst examples in the nRFgo SDK (enhanced_shockburst_ptx_nrf2 and enhanced_shockburst_prx_nrf2...
Hi, I have an nRF24LE1 based sensor, transmitting to an nR24L01+ connected to an arduino (i know you don't supportit). I have LE1 to LE1 TX/RX working (as a test case). I...
Is there a way to disable (not use) the peer manager's whitelist without setting it to NULL? I'd like to be able to temporarily disable the whitelist without potentially losing...
Hello,
I'm sampling the ADC using PPI like in the saadc example of the sdk12. For the ADC I use
TIMER 1.
And I want to write those ADC values on a SD Card over SPI...
Hi,
I am interfacing micro SD card with nrf52 using fatfs example in sdk 12.0. As I am beginner, first I wanted to perform operations like read, write, delete and some...
I have erased my J-Link firmware in error! after having installed the version supporting V6.12a, however that upgrade wasn't achieved via the drag and drop process.
Where...
Hi,
I am looking to test the performance (range, data throughput, packet drop rate etc.) of BT5 in application specific setting using nRF52840. Ideally this would be done...
What has been tested:
In the Bootloader configuration inside the watchdog and start and
feed the dog operation, and then in
the static void wait_for_events
(void)...
Hello,
I am working on modified version of ble_nus example and I tried to send data to nordic DK.
In Android, I used
BluetoothGattCharacteristic characteristic = mBluetoothGattService...
Hi,
We are designing a system that shall supervise the battery voltage (1 AA cell) on an analog input to the nRF51822. Question is what happens when we put the processor...
Hi
I'm doing project called automation of lights using beacons and iam using sdk (nRF5_SDK_12.1.0_0d23e2a) and nrf51822 dongle. I need complete information about advertising...
Hi,
I am using nrf51 dongle on which I have loaded example code for BLE central(ble_hrs_c) from SDK 11.0.0 's example folder + soft device S130.
My problem is, I am...
