Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
I am developing a robot controller(Central, nRF51822).
However, I am having a problem with UUID.
And I am using the ble_central (s130 ble_app_uart) example.
The figure...
Hi
I am developing a bootloader for nRF52840 using SDK 15.2.0 and s140_nrf52_6.1.0_softdevice, that should support both USBD and BLE transports.
The first transport layer...
We are using NRF52840 with Softdevice 340 and several sensors connected via ANT and BLE. NRF is connected to STM32 via serial UART connection and use ANT serial protocol for...
I am using PPK to measure current. The system uses 2 CR2430 in parallel.
I observe that
1. When using the battery as external supply, the battery voltage drop to 2.5V...
I am using the original board. It does not have a 32kHz crystal.
So I want to use the built-in RC oscillator.
In addition, use the time example of nRF5_SDK_16.0.0. "NRFX_CLOCK_CONFIG_LF_SRC...
Hello,
I am using nRF52840 S140 v7.0.1. I have few queries on DTM functionality.
1) As per standards, we can do DTM test either by sending HCI commands or UART commands...
Hi,
Using Eddystone example I configured EID and TLM slots. I see in nRF connect app both EID and encrypted TLM(encrypted data, salt, MIC).
How to exactly decode the...
Hello,
we are experimenting with the Nrf52811 CTE feature and have a few doubts concerning the documentation. We program our experiments with bare-metal (no soft device...
Hi,
I am working on one business use case. The basic requirement is to monitor the outdoor air environment from different locations. I want to try out the initial things...
Hi,
For nRF52840 BLE, in the DFU (OTA) example (buttonless OTA):
../nRF5_SDK_15.3.0_59ac345/examples/ble_peripheral/ble_app_buttonless_dfu
How scanning is done? Or where...
Hello, I'm using Zigbee SDK 4.0.0 with Segger Embedded Studio 4.30 and custom pca10059-compatible debug board.
I ran into difficulties when trying to subscribe to attributes...
Hi,
I am using custom gatt service & I have included some of the code which supports swift pairing from ble_hid_mouse example. Here is my sniffer log -
& the jlink rtt...
