Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi,
I'm developing a router Zigbee device starting from light bulb example.
In the example the function zb_set_max_children is called passing 10 as parameter.
About...
Hi,
I am using
PCA10056
SDK 15.3.0
Keil IDE
The soft device is S140
JLinkRTTViewer for debug
I am testing background serial-dfu.(refer to https://devzone...
Hello,
We are working with the nrf 9160 dk.
We need to use internet connectivity to send an http get and post to a remote server.
We want to utilize the NB-IoT...
I've been developing firmware for my PCA10059.
I load the package with nrfutil dfu usb-serial --package=_build/t.zip --serial-number=`cat /tmp/serials.txt` --connect-delay...
I use nRF5_SDK_15.0.0
My soc is NRF52832,project is based on ble_peripheral ble_app_blinky.
After I call idle_state_handle() let my device go to sleeping.
Sleep current...
Hello,
We are using nrf52832 with sdk 16.0, for a particular reason we are storing some variables in flash storage, i have some question regarding that
what is the time...
Hello,
I am developing a driver that can handle cryptographic operations and I am using example code from nRF5_SDK_16.0.0_98a08e2 /examples/crypto/nrf_cc310/aes to get...
I have a Segger J-Trace Pro and am attempting to enable trace debugging of my application. I have a custom board that breakout out the appropriate Trace Clk and Trace Data...
Installed nrfutil with python 3.8 and pip3 20.0.2 on Windows 10 Trying to run dfu over usb-serial: nrfutil dfu usb-serial -pkg FW.zip -p COM4 -b 115200
I get the following...
Hello,
I got a problem with the nRF sniffer for Wireshark. I got the following configuration:
Board: nRF52-DK pca10040
Hex file: sniffer_pca10040_129d2b3.hex (provided...
Hello:
nRF52840 UART peripheral receiver FIFO reset
Whenever there is a receiving error ( Frame error or Break error or any) , I would like to reset the receiver's FIFO...
I have an application that requires mains power for lighting with a BLE receiver that is permanently advertising and scanning and I need to be able to dim the lights. My circuit...
Hi
I am new to nordic processors.
I am using spi_ pca10040 project as a reference for my custom board. On my board the SPI pin configuration is different from pca10040...
