Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
the latest Errata sheet of the nRF52840 lists number [228] RADIO: No interrupt is generated for SYNC event.
Checking it, I was a little bit surprised finding actually...
i am using BLE template from examples BLE Peripheral and adding some custom characteristics and not changing any advertisement data. But the device is advertising with only...
Hi,
I want to set up visual code studio for development. I was able to successfully run the blinky app on PCA10040 board and also emulated PCA10040e example.
After this...
Hey folks,
I don't know what's the problem but I am really struggly to implement a simple UART into my heavily modified BLE Multilink Central Example (SDK16)..
Maybe...
Hi,
In my application, I would like to transfer data from MCU ---(UART#1)---> BLE#1(Peripheral) ---> BLE#2(Central) ---(UART#2)---> PC. I start my code based on ble_app_uart_pca10040e_s112...
I am using nrf52840 pdk for sniffing zigbee network. After flashing firmware from this link on board . After connecting nrf usb port to pc , windows giving error "Unknown...
I am receiving repeated POLLHUP and reboot on my nrf91DK board (see attached log).
1) I have loaded the modem firmware with mfw_nrf9160_1.1.1.zip. (I also tried version...
Hello Nordic,
I have a sparkfun nRF52840 mini and I want to know which project from nRF5_SDK_15.3.0_59ac345 should I use to have my nRF52840 slave in the TWI communcation...
I am currently working from an SDK16.0 peripheral example utilising freeRTOS and polling the softdevice (NRF_SDH_DISPATCH_MODEL == 2).
This has worked fine for nRF5 SDK...
I have some problems with the TWI (I2C) and it seems that TWI1 does not send anything. I have managed to create a simple example to recreate the issue. I am using TWI1 instead...
Hello.
Is it possible to send more than 1B data via blinky characteristic from central to peripheral? I made my project with two characteristic (my own 128-bit UUID) basing...
I am using android ble with kotlin. I ported the Blinky example to kotlin. There is a reference escaped in object construction when on construction the BLEManager invokes...
Dear Nordic Team!
I am verifying my tools chain for nrf52840 Mesh project development by mesh light-switch example. I have 4 PCA10056 and make them to 1 provisioner, 1 client...
Hi,
I use sdk16 and nRF52832.I want to change advertising in the air:
Now I'm using the timer to change the adv.But I want to change adv with RF interrupt.
Like this...
