I am in need of the usb-to-uart.hex firmware and the driver for it. This is required to test the radio dongle nRF24LU1+ device (32k) whether it can be programmed through USB...
I've been unsuccessfully trying to serialize BTLE example programs by SPI. I have two PCA10028 boards and I'm using SDK10. In addition to serialization examples, I've tried...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hello,
Connection between linux router and NRf51 devices worked before I've updated kernel version from 4.09 to 4.3.
Now, with the same configuration and hardware, I'm not...
Hi
Does anyone know a CE—certified module based on the nRF24LU1+? Ideally, it should have an SMA connector, but any kind of antenna would be fine.
There are many modules...
I am running peripheral example radio test example on PCA10001(part of nRF51822 Evaluation Kit). using nordic sdk v7.
I am using mincicom on linux at baudrate of 38400...
Hello!
I am trying to get windows phone work with nrf_uart example on nrf51 dk board (pca10028).
I am using SDK 9.0 with S110 softdevice ver. 8.0.0.
I was using examples...
Hello,
I am using nrf52832 Dev Kit and am attempting to send information using the ble_app_uart example under SDK version 15 (I don't know the exact rev, but I downloaded...
Hi,
I am using nrf52832 in my custom board and I want to make secure connection between my two boards using stored keys.
Is there any example provide by nordic which I...
I am using the nrf51822 ble with s130_nrf51_2.0.0_softdevice and want to know if the broadcast can start at a given time, and if the adv_ interval can change everytime? (such...
Hello, basically I want my nRF9160 DK to establish a secure connection with DTLS by using mbedtls .
What I'm trying to do
I'm currently working with the LwM2M sample...
Hello,
My NUS services work fine i can transmit and receive data over UART , but i still get this error in my nRF Toolbox (UART) . Any help will apreciated
Some user datas have been stored in a special page of flash in nRF52832 . However , I need to reprogramme the chip through bootloader , and make sure the user datas not being...
Hi,
I am trying to evaluate the nRF52840 development boards and configure as a simple switch and light node.
The first issue I have had is that on a Huawei phone the nRF...
Hello,
I am trying to find out where to put my persistent storage data in flash.
I have to set start_addr and end_addr, to use fstorage, but I dont know what addresses...
Dear Nordics,
i'm getting started with development on Laird BL651.
Issues as follows:
It appears to be neccessary to switch to internal RC oscillator and adjust the...
Hi,
We are facing an issue related to battery life. We are using sdk 15 and SD S132(7.0.1) and we are able to archived 30uA current consumption, but we want it near to 5uA...
Hello,
I am using SDK v11, SoftDevice v132 and Keil Uvision 5 to program on my nrf52832 SOC on the development kit(PCA10040) for our project. I need to save a few uint32_t...
I am trying to evaluate the nRF52840 and can't find the source code for any of the project - only the hex files to run applications.
Where can I find the source code?
...
Hi,
We have developed a mouse with nRF52832 using the ble_app_hids_mouse example.Now, I would like to add consumer usage into the hid descriptor to control media. So, I...
Hi,
I am currently working on nordic PDK. And I am interested in flashing nRF52840 through FTDI SWD interface. I want to know whether it is possible?
If yes, what will...
