I will be selling various ble products. My customers can connect to and program the devices using their bluetooth smart phone or tablet.
I want them to have the option...
Hi,
I am trying to run nRF24L01+ in default configuration using simple ping-pong examples using RF24 Arduino library.
The problem is that while ping-pong is getting through...
Hi,
I want to send data from one peripheral(nRF51 DK) to multiple Android Phones. This will be a one way connection from the peripheral to the smartphones. I red on the...
I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hi,
We have a stability issue with nRF52840 DK after it has been upgraded to JLink DLL version V6.60e and firmware OB-SAM3U128-V2-NordicSemi compiled Jan 7 2019 14:07:15...
I have been looking into using Bluetooth Low Energy 5 advertising features like periodic advertising and advertisement chaining, but have not been able to have any luck with...
hello
we want to connect FPGA to 52840 using QSPI interface for data transfer, 52840 used as master, and FPGA as slaver. so we use write opcode PP4O for 4 lines writing...
Hello,
I want to read two files from SD card using nRF9160dk. I tried this code ncs/zephyr/samples/subsys/fs/fat_fs.
The Code:
I am getting the following error:
...
I need FreeRTOS operation in my build. I've adopted the FreeRTOS.h file from the blinky_freertos example, unchanged aside from a larger heap size and setting INCLUDE_xSemaphoreGetMutexHolder...
Hi all,
I have the nRF51822 chip and I want to acquire external sensor (i.e. pressure, temperature) and send the information via bluetooth.
I need to configure the I/O...
Hi
I using nRF52840-DK with 64 Mb external flash memory.
I'm using SPI interface for read / write command with the external flash.
When I'm using single command for...
I am attempting to implement AoA using the nRF5340 Preview development kit and 3 BMD-360 modules with the nrf2811 SoC.
In searching the devzone I see multiple comments...
Hi ,
I am following the instructions here:
https://bifravst.gitbook.io/bifravst/bifravst-on-aws/simulator
to deploy the web application, and the web application says...
Based on SDK15.3(nRF52810) app_uart example, stop the adverting, turn off all the peripherals and enter idle_state_handle(), but the static current is still about 10uA. Rememeber...
I set up the environment for the nRF9160 as it was specified and downloaded the git-hub code https://github.com/NordicPlayground/fw-nrfconnect-nrf (environment 1) and I tested...
Hi all,
I am using 2 SPI's in my design. I enabled SPI0_ENABLED and SPI1_ENABLED in my sdk_config.h.
SPI0 works fine. But SPI1 MOSI pin always sends 0xFF.
My pin configuration...
Hi, I m sending a packet in mode Nrf_1Mb to another board nrf5340-PDK.
When I try to enable NRF_REGULATORS_S->VREGRADIO.DCDCEN=REGULATORS_VREGRADIO_DCDCEN_DCDCEN_Enabled;...
Hi,
I am using mesh SDK v3.2.0 and SoftDevice(s140 v6.1.1) to build light switch server firmware. And also insert the uart code from nRF5_SDK_15.3.0_59ac345. So the light...
Hello:
I am studying thread samples in nRF9160.
There are two thread samples: "zephyr\samples\basic\threads" and “zephyr\samples\synchronization”.
But I can't find main...
