Hello,
I would like to do an communication between Arduino and Android platform.
In my case, Android will be master.
But I want also test between 2 Arduino with an Bluetooth...
Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
Hi All,
Does anyone know what the maximum altitude is available for the nRF9160 GPS?
I know some GPS devices stop working properly if above pre defined heights.
The...
I have a PCA10040 board and use the development soft of SEGGER Embedded Studio for ARM 4.50.
I ran the project \nRF5_SDK_15.3.0_59ac345\examples\ble_peripheral\ble_app_beacon...
While I was working with my dev kit this morning, the board has suddenly stopped responding to commands.
When I attempt to connect via jlink using Segger Embedded Studio...
This is definitely a stupid question but the uart ble example is littered with the likes of " NRF_LOG_INFO("Connected");". Where is this printed and how can I view it? I can...
Hi,
I'm using latest master branch of nRF Connect SDK and pre-released modem FW 1.1.2 which is including ANT->AUX switching. I'm developing a firmware for a custom board...
Hello,
is it possible to use use timeslot API on s140 while BLE is in "central" mode?
I was able to use timeslot API when BLE was running as peripheral. However, same...
Hi,
I need the bigger the size of bootloader. So I changed IROM1 0x78000 0x6000 to IROM1 0x77000 0x7000.But nrf_dfu_transports_init returned error code after I changed the...
Hello I would like to use the malloc function but the function send me all the time a null pointer... I have the same problem on all examples. In this case, I use the "ble_thread_dyn_template_pca10056_S140...
Dear all,
the latest documentation I have found for the "nRF5x Command Line Tools" is version 9.4.0. Is this still valid and sufficient for the recent version 10.7.0 ? ...
I have a BLE device which I can connect to with nRF Connect on Android (v. 9, Samsung Galaxy S8).
After disconnecting in the devices tab, the connection is opened and closed...
Hi, Im developing a Zigbee concentrator. I used nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730 ble_zigbee_template as start point of my project. The project is full working...
Hi Nordic,
There is a question about the default setting for Advertising PHY type. if there is no config value setting like case (PHY_1M ) . (all memory already set to 0...
Hi,
can you please tell me in what cases I get this assertion?
SOFTDEVICE: ASSERTION FAILED, PCxxx: 0x25252
For background: using the timeslot API works for about...
Hello!
I have Nordic dev board 52 and I would like to establish communication nrf52832 -> (one way) computer com port and advertise/send data line by line from nrf52832...
